Top 20 Frigidaire FEF336BC Electric Kitchen Range Questions & Answers

There are mounting plates that recess the plug in the wall. Hardware stores have them in the electrical parts department.

Hi Friend, this is Z. Thank you for your inquiry! Based on the symptoms you are describing, you may either have a communication error from the main control board or a potential wiring failure. You may try and reset your range by disconnecting the to your range for up to ten minutes by flipping the circuit breaker off and back on. If the issue proceeds, then it really could be a hit or miss calculation in parts so I would personally reach out to an experienced tech that will be able to identify the precise reason.

Good Afternoon Friend, I understand that you are receiving an F13 error code on your Tappan range. I suggest resetting your appliance, by either unplugging it or shutting the power off at your home's circuit breaker, for 3-5 minutes. Restore power. I ask that you please follow up with a comment on the post, at your convenience, to advise if further troubleshooting is needed or if your washer status has changed successfully. If further troubleshooting is needed, I ask that you please leave your model number in the comments as well. Hope this is helpful. -Best Regards- WP

Check your circuit breakers in the power panel for a bad breaker. The breaker has a pin connecting both handles One breaker can trip without tripping the other. This condition will only allow 115 volts to operate the controls and light bulbs but will not power the heating elements.

Good Afternoon Patti, I understand that your Hotpoint stove digital timer/clock is beeping and you are wondering how to disconnect it. I suggest resetting your stove by either unplugging it or disconnecting the power at your home's circuit breaker for 3-5 minutes. When power is restored, if your stove is still beeping, I suggest contacting your local authorized technician. They will be able to diagnose your appliance and determine what the cause of the beeping is. They will also be able to assist with repairs, if needed. Hope this is helpful. -Best Regards- WP

Good Afternoon Paige, thank you for your post! Based on what you have described, it sounds like you either have a wiring failure or your burner is faulty. In this regard, it is best to contact a professional to proceed further. Best regard! - Z

Good Afternoon Friend, this is Z. Thank you for your post! I understand you would like to know the price of the circuit board of your oven. Can you elaborate prior to your problem any other symptoms? For instance, did notice any error codes, or other strange functions? Also, may I have your model number please? You can typically locate the serial tag (which lists your model number) in the storage drawer, on the right side. With this information I can assist you better in pinpointing the problem before you take this step?

Good Afternoon Dave, I am happy to assist you! If only the large element of your Frigidaire range is not working but the other elements do function, then it sounds like the element itself might be faulty. Otherwise, your appliance is experiencing a potential wiring failure, switch or a communication issue with the EOC (Electronic Oven Control). This is not a normal DIY job so you might want to reach out to a local professional to determine the exact diagnosis. I hope this information helps to some degree.

Good Afternoon Lyle, thank you for allowing me to assist you! Typically error code F1 indicates that a runaway temperature (overheating) issue has been detected. Let's try reprogramming your range by either unplugging it or flipping the household circuit breaker off. It is important to wait roughly ten minutes and then turn your range on. If the error code does not clear, at this point, I would suggest contacting a professional to proceed further. Most likely the RTD Probe (Resistance Temperature Detector) or the EOC (electronic oven control) will need replacing. Hope this helps!

Hello Zena, thank you for allowing me to assist you! Let's try reprogramming your range by either unplugging it or flipping the household circuit breaker off. Wait roughly ten minutes and then turn your appliance on. An experienced service technician may need to further evaluate this issue if it was not resolved with the power reset. Your range could possibly be experiencing a potential wiring failure, faulty EOC (electronic oven control), sensor probe and/or bake or broil element(s). I would strongly recommend consulting a professional to narrow down the precise issue before investing in parts that may or may not be the root cause. Best regards!

Hello Edward, thank you for your post! Remember, these intricate part replacements do require precision and patience, therefore when replacing parts that require the exchange of electrical wiring harness or removing your range, I always suggest seeking professional advice. One must be very careful as these replacements can lead to any potential harm. Best regards!

Hello Tom, thank you for your post! I understand the burners on your Frigidaire range, FEF336BC, continue to stay on. Try resetting the unit by either unplugging it or flipping the household breaker to the off position. Wait approximately ten minutes and then turn on your range. If these troubleshooting steps prove ineffective, you may wish to contact a professional as your range may possibly have a potential wiring failure, faulty EOC (electronic oven control) or burners.

Hello Sunny, it is my pleasure to help you. Generally, error code E69 means that the unit is experiencing high voltage incoming power supply. One of the best ways to determine if this is a false error code is to reset the power to the appliance by either unplugging it or flipping off the breaker for about 30 seconds. If the error code persists, it could either be a faulty terminal block or EOC (Electronic Oven Control). In that case, a certified technician would generally replace the faulty part after proper diagnosis. I hope this information helps in a some way.

Hi Renay, thank you for your post! If you are getting an error code F20, it usually means that your range is experiencing a potential issue with the UIB (User Interface Control). I would recommend, however, running a quick test to ensure that this is not a false error code. You do this by resetting your oven by flipping the breaker or unplugging it for approximately ten minutes. If resetting your range does not correct the issue, please reach out to an expert technician to ensure the appropriate replacement part is ordered and is installed correctly to prevent future issues. I hope this information helps to some degree - thanks for your question, and please do not hesitate to reconnect.

Hello Robert, thank you for your inquiry! I understand your display panel is only partial. Some possibilities why this may be occurring include issues with your appliance's power supply, being plugged into a GFI outlet, display toggle, or a faulty control panel. I always recommend resetting your cooking appliance first. You can do so by unplugging the range or flipping the circuit breaker for about 30 seconds and then turning the appliance back on. If the instructions above do not solve the problem, I am fairly confident that an authorized service agent will be able to restore your appliance to its normal operating condition. You can often locate a qualified service technician on the manufacturer website. Thanks for allowing me the opportunity to assist you!

The oven control board has shorted out and will need to be replaced. Here is that part to order.There is also a video on that parts page to show you how to make the repair.

The temp. probe needs to be replaced. Here is the part to order.

Hi Donna, I am happy to assist you! If the oven door is locked with door closed, try pressing the CLEAR/OFF or CANCEL button in for approximately three seconds if your unit is a touchpad model. If you have a knob type range control, I suggest starting a self-clean cycle. Then turn the stop time knob to the off position. If that does not work, then disconnect power to the stove and then reset unit by either unplugging it or flipping the breaker off. It is necessary to wait roughly ten minutes and then turn the range on. I ask that you please follow up with a response on the post, at your convenience, to advise if further troubleshooting is needed or if the unit's status has changed successfully. Best of luck!

warm

Your heating element maybe burnt out.