20 Most Recent
Roland FP7F-BK [BLEMISHED ITEM] 88-Key Digital Piano in Black - - Page 3 Questions & Answers
I have a roland keyboard mixing amplifier, KC-550.
The KC-550 is a MONAURAL amp and since the Ipod emits STEREO you have to use a special cable to MIX both the left and right from the Ipod into a single, monaural signal.
You can MAKE a cheapy mixer that will serve your purpose by using a series resistor, say 1K from each of the two Ipod output channels to go to the single mono input to the KC-550.
I would build it this way: Find an old IPOD cable or any 1/8 inch stereo cable and seperate the two wires and the shield. In a 1/4 inch plug, connect the shield from the Ipod cable to the shield (barrel sleeve) of the 1/4 inch plug. Connect one lead of each of TWO 1K resistors to the TIP connection of the 1/4 inch plug. Connect each of the two signal leads from the Ipod to the two remaining floating resistor leads. Insulate the splices.
DON'T forget to put the shell for the 1/4 inch plug over the cable before connecting the cable to the 1/4 inch jack. All parts should be readily available at Radio Shack.
I don't know that I have ever seen a suitable ready made mixer cable for this function.
I need a power transformer for roland sde -3000
If your transformer is fried then you will have to replace it of
course, but if it has only opened the thermal fuse that is tucked into
the primary windings then you can replace that and not have to replace
the entire transformer. Be sure to use the same temperature and
type thermal fuse as the original. You will find the thermal fuse
tucked in where the ac power in wires go into the transformer and you
may have to clear some plastic out of the way in order to get to
it. Be very very carfull that you do not nick or cut or break any
of the magnet wire that makes up the windings of the transformer.
Good luck.
Roland amps
Hi rockbert
Yes you can do this. the only drama you may have is at high levels where one amp may begin to clip and distort before the other. If you are trying to run a stereo setup, you could counter this to some degree by adjusting the bigger amps gain down to the same level as the smaller amp if needed, giving you control over the "stereo balance".
I am more than happy to answer
any other questions you may have about it, just give me a hoy :) If you
are still unsure, or have problems, then before you give a rating for this advice, please
get back to me and we can try some more things.
Thanks for using FixYa, If you consider the advice I have given you
as sound, a FixYa rating is a great reward for my efforts to help
you. Cheers.
regards
robotek
How do I change to degree mode on my porpo YH-2000
- Power Off: Turn off the device.
- Jumper Configuration: Locate the jumper labeled "S16" on the device. Initially, it should be connected to pins 2 and 3.
- Power On (Alarm+All LEDs Flashing): Turn the device back on. You'll see the alarm LED and all other LEDs flashing.
- Power Off Again: Turn off the device once more.
- Jumper Adjustment: Change the jumper configuration from pins 2 and 3 to pins 1 and 2.
- Finished: Your Porpo YH-2000 is now set to the desired angular unit mode.
If you encounter any issues, you can press the reset switch on the back of the device to reinitialize it.
Openfit Shokz battery replacement?
Question edited for clarity, typo and CAPS.
Question moved from Cars and Trucks category.
Claim on the warranty irrespective of how long you have had them. They charge $180 but they cost them $20 to buy from China. Package them up and send them tracked and ask them to replace the batteries.
How long is the warranty on AfterShokz?
While we hope you never need it, all new Shokz purchased from authorized retailers come with a two-year warranty that begins on your date of purchase.
Jan 11, 2019
https://www.google.com/search?q=Openfit+Shokz+battery+replacement
..
My roadking rk4000 wont charge. I turn it off to charge it but there is no indicator light at all, any suggestions?
Are you using the charging cables that came with it? That is a type C. Are you securely attaching the charging cable? A loose connection would keep the battery from charging. If you had a low battery, you would see a red light. That you have no light at all suggests there is no charge left in the battery. I'm not sure the reset will work with no charge which is why you ought to check the cables first.
But turn it off and then hold down the Multifunction button for 10 seconds to reset it. Then turn it back on and see what happens. If you can, test the charging cable on aother device. If you have another type C charging cable, try it, just to eliminate a bad cable. If these suggestions don't work, you may try the manufacturer's customer support.
Can f2100 remote work on my dishtv box?
The F2100 remote is not explicitly listed as compatible with the AerialBox T2100, I recommend using the remote that came with your AerialBox T2100 for optimal functionality. If you have any specific compatibility concerns, I suggest reaching out to Dish TV customer support for further assistance.
Audiosonic CR-06PL not changing time when following manual instructions.
Set Time Hours and Minutes: Press Time/12/24 and Alarm1/ON/OFF buttons at the same time for two seconds and it will start to blink the hour.
Press and hold the button for a fast setting or tap it briefly to increase the setting by one hour. Now set the minutes with time (press and hold) and min.
How do I set the Audiosonic clock? Set current time Press and hold the time button and simultaneously press the hour to set the hours in 24-hour mode .
Not finding what you are looking for?