Canon MX300 Office All-In-One Printer - Answered Questions & Fixed issues

See this video for solution for error code 5100:

Error no 5200 is caused by its temperature high.. to solve your problem follow the instruction given below::

1. Turn Off printer, cable power still plug in.

2. Press Stop/Reset button, don't release the button.

3. Press Power button by holding without release and than release Stop/Reset Button.

4. Press Stop/Reset button two times (2x) now release the Power Button.

5. Wait until service mode to zero (0).

6. Turn off the Printer, cable power still plug in.

7. Press Stop/Reset button, don't release it.

8. Press Power button don't release & than release Stop/Release button.

9. Press Stop/Reset button four times (4x), wait until service mode to "1"

10. Turn off printer, and loose cable power, wait for one (1) minute.

11. Connect cable power, turn on printer again, now this printer ready to use.

You might try a hard reset of printer along with uninstalling and reinstalling the software for the printer. If nada, you might give Canon a call and ask their techies for their feedback on situation.

on the test print paper there should be a set of numbers there (prints automatically after align print head is done), these will need to be added into the prompt that comes up in screen after "set value" shows up, but unless a major rebuild has just been done to machine I find this is rarely needed to be done < I just select skip or done to exit that mode

open the top and check for any loose paper jams.then use some alcohol on a q-tip to clean all the rollers.

http://gdlp01.c-wss.com/gds/5/0300000425/01/mx300_qsg_us_v1.pdf

Have you downloaded or installed the full software for it? If so can you open the program first and initiate the scan from it?

sometime my printer does the same, print something and see how the black color is, if it is printing or it is the color ink that needs to replace also. i just keep printing until the ink get real light then i change them.

The fix for that error simply says to open the door by hand. If that doesn't fix the issue you need to contact a service center.

reinstall the printer drivers

Printer fails to detect the ink levels. Either replace the ink cartridges (as you may have got a defective cartridge) or deactivate the level detection on the printer. Hope that helps!

Restart your printer. If it doesn't solve your problem, search the necessary manual here Canon Copier MFP service manual and schematic diagrams circuit

Use the quick start guide on this page. Canon Support Drivers PIXMA MX300

was the ink you put in a new canon ink cartridge? Did you take the protective covers off the ink?

This may sound silly, but make sure your cables are fully connected to the printer and your power cable is plugged in to the electrical outlet. Once, I received a phone call from a friend who was messing around with her printer for over an hour. She couldn't get it to power on. I went over to her house and immediately plugged it in... voila! It worked. ;)

If you know more about these error codes, check the site linked here. If is not practical to include all the details here by this window. http://electronicshelponline.blogspot.com/ Pull up previous posts by its left sidebar, or type in the brand name and model number to of your set, to its search box, and press 'Enter' or view it in Mosaic / Timeslide option.

The printer hardware should even this out when printing. You should also ensure the paper meets the automatic feeder requirements of the printer. If printing is skewed, feeding multiple pages or jamming, please follow these instructions (use a regular letter size paper to test after doing the steps given below): Please check to ensure there is nothing obstructing the paper feed mechanism down inside the printer where it is not easily seen. If there is nothing obvious, unplug the printer and remove the paper. Open the front cover and look above the steel rod. You should see a conveyor belt with rubber teeth on it, like a fan belt. Take the bottom part of that belt and move it gently to the left. The cartridges should come out with it. Make sure the cartridges can move fully from one side of the printer to the other. Check also the output rollers on the bottom of the printer for any blockage. If it is jamming under the carrier assembly, you may be able to fix it using the manual feed slot. Turn the printer off. Next take a #10 envelope and feed it through the left side of the paper feed slot (The manual paper feed slot is preferred, but the automatic feed will do if there is no manual paper feed for this printer) until it comes completely through the printer to the back of the exit rollers. Move it up and down and slowly move it over to the right side. If something is stuck under the black guide plate this may work it loose or you may have to feed the envelope through the front rollers and push your way backward (please be careful here). Next, take a damp warm cloth and clean the rubber rollers in the automatic sheet feeder. Dust may be coating the rollers there and as they become less tacky, they cannot feed paper correctly. Finally, turn the printer upside down and carefully shake it for 10 to 20 seconds to see if something falls out of the paper feed path. Then plug the printer back up, take your paper out and replace it with a fresh, small stack (about 5 pages) of paper. Quickly bend the stack in an 'S' shape a few times to separate pages. Make sure it is lined up on the right side of the paper feed and the paper guide on the left is snug on the left side of the paper. Then try to form feed again. If that works, then try to print again.

Remove the paper, use a cloth and isopropyl alcohol, clean the rollers carefully, let dry insert paper neatly in tray to the stop.

Press down "STOP/RESET" button - 5 seconds

You may download the software and drivers from here.