20 Most Recent Canon MX300 Office All-In-One Printer - Page 7 Questions & Answers

Please reset the printer

1. Turn off your printer
2. Press and hold the STOP/RESET button
3. Press and hold Power ON button
4. While holding the Power ON button, release the STOP/RESET button
5. While holding still the Power ON button, press twice the STOP/RESET button
6. Release the Power ON button
7. Wait until it display an "idle" message. It will take about a minute.
8. When "idle" appear, open the top cover to expose the cartridges.
9. Lift up the cover for cartridge holder and take out both the black and color cartridges
10. Return the cover of cartridge holder and turn off the printer
11. Return the top cover and turn on the printer again
12. After the printer initialize, return the cartridges.

1. Press and Hold the STOP/RESET button and wait until it self restart.
2. Release the STOP/RESET button the the printer is restarting.
3. Wait for a few seconds

http://dikma.web.id/atasi-error-5200-pada-printer-canon-mx328/

the printer was unable to detect the cartridge.

remove the two ink cartridges from the printer, both the black and color

clean the contact surface ( the surface where the terminals inside the printer touches) with a clothe moistened with alcohol.

after cleaning the contact, return the cartridges back to the printer.

see how it goes.

On the same screen that you would put for scanning.

You have to refill both.

Hi


Please go the canon service center this the best. bcoz u r not familiar with hardware.

censorship is dirty

Ensure you have the taskbar installed for the printer available here. Just select the correct version of windows you are using to shorten the list on the link

http://www.canon.co.uk/Support/Consumer_Products/products/Fax__Multifunctionals/InkJet/PIXMA_MX_series/MX300.aspx?type=download&page=1

Hi,

The C-CRT is an alert that you need to replace the Colour Cartridge. Likewise, if you ever get B-CRT it means you need to replace the Black Cartridge.

Try this method to get the ink flowing:

1. Simply fill a saucer with approx 2mm of just boiled water
2. Place the print head in the saucer with the head in the water.
3. Leave the head in the water for approx 2 - 5 Mins
4. The Heat will assist in dissolving any blockages and help the ink to flow with out using any chemicals.

If it is a compatible cartridge you have used then it is possible to get a failure. Most are re-manufactured and are not 100% Reliable.
Also make sure the contacts on the inside of the printer are clean and all there. sometimes they can be damaged by removing and replacing cartridges. these can be cleaned with alcohol wipes.
I hope this helps Regards GM

do the same again, there are free answers, this question was one of the free ones.

you have to remove the ink cartridges. Using a clean clothe moistened with alcohol,wipe the dirt at the surface contact of the cartridges. This contact is where the terminal inside the printer touches.

post back if this will not help you. I'll provide you with another solution.

You might remove the print cartridges and inspect the printheads for contamination. If they look at all smeary, gently clean them with cotton swabs and window cleaner, nothing stronger. Good luck-

Have you tried upgrading your XP O/S to Win7 this may cure the problem.
hope this helps.

Is verry bad,the printer have logic board defect....you need to replace the logic board.I look in the service manual and 9000 error means to replace the logic board.If i have been useful please give me a vote :).Thanks

Press either an "Ok/Select" button or the Green button.

Possible that the printer requires a resetting so remove your printer from the PC and un-install the printer software. Now reinstall the printer software and connect the Printer to be detected and installed. Check printer properties to see the ink levels.
Use head cleaning before a test is taken . It is possible that the head is not reacting to the need of the command , can be an issue with ink drying , can also be poor ink cartridge contacts