Zonet ZSR3104WE 802.11G MIMO WIRELESS BROADBAND ROUTER - Answered Questions & Fixed issues

not a router question

Contact AT&T, have a tech come out and analyze the signal. You have checked and verified ALL cables inside, right?

First , Check/swap ALL cables, If you are sure it not inside. Contact your ISP and have a tech come out to analyze the signal, it may be outside. I had a similar issue I traced the cable all through the house to the cable entrance, the tech found a underground box that had been run over by a large lawn mower breaking the box allowing water to enter.

Username: Admin
Password: Admin

There you go

Go to your router, you can do that by simple going to a browser and then put your gateway in it. You will be asked for a password, after that you can now change the MTU setting in your router.

Aqui pudes bajar el manual, y la instruciones (en Ingles) estan en la pagina 26:
http://www.zonetusa.com/ProductDownload/UM_ZSR3104WE.pdf

Buenas Suerte,
copy and paste the link into your browser.
If I could be of further assistance, let me know. If this helps or solves the issue, please rate it.
Thanks, Joe
I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Back when P4 systems were common, the hard drive interfaces were quite marginal for video processing and techniques to force the capture to faster devices (like a RAM drive, or now SSD drive, or SCSI interface to high end striped drives) were used to smooth the video capture. I have had good luck with SATA3 interface SSD's for capturing video, but continue to use a drive other than the one I boot from so windows doesn't mess up the frame rate.

Normally 12v and less than 1A

First: GENERAL ROUTERS RESETING Second: http://www.fixya.com/support/r7900574-general_router_setup

POORLY supported routers made in China. STRONGLY recommend disposing of this device and obtaining one from a better vendor that supports it's products i.e.: Cisco, 3Com, etc...

Contact seller or company that makes it. May be a download item on maker's site.

You could try Getright software, but most likely you are having connection problems (low bandwidth or high error rates). Problem is not likely in the router unless your wireless signal strength is very low.

It's not a big deal. The base address may vary for various routers, and you can adjust it according to your current network configuration (I mean other TCP strings)

In order to fully answer your question, a number of needful things must be inspected, reinstalled, confirmed, & tested:

1. Reset. Try the reset button. You could use a paper clip to reach the reset button through the pin hole in the lower front left of the Zonet KVM unit.
2. Inspect connectors. Each data/input/power connector/port requires all of its pins to be present & straight for full functionality.
1. Inspect the entire length of each cable & cord to ensure that each has no damaged area.
2. Seat each connector in the appropriate port of a computer that will be accessed via the KVM unit.
3. Electricity. Inspect all affected devices & confirm that each has sufficient, uninterrupted electricity.
1. It is possible for a Zonet KVM unit to display channel lights without direct power to the unit, but you should confirm that the unit is getting sufficient, uninterrupted electricity-directly through its own power cord. Unplug the KVM power cord & every connector & reseat each one (this performs a power reset on the KVM unit)-making sure that each connector is in the correct location (not just where it originally was). Thus, make sure that the keyboard, video display (monitor), & mouse are on the output side.
2. Press the power button on your monitor. If it does not turn off the monitor's power status light (Off/On/Standby), then remove the power cord from the monitor & reseat it-to reset the monitor's hardware. If it does not turn on the monitor's power status light, then the monitor is either not getting enough electricity or it has a malfunction which requires troubleshooting & fixing (possibly through a fixya.com thread for that monitor model).
3. Unlike USB devices, PS/2 devices usually require device connection prior to turning on that device. With that said, connect the keyboard & mouse KVM channel cable connectors to the computers & then turn on those computers that you intend to display through the KVM-connected monitor & then turn on these computers.
4. Any computer that does not turn on has an issue that requires resolving (just like a monitor that would not turn on).
5. Sometimes a keyboard/mouse interface issue can be resolved by replacing that interface device.
4. The KVM Unit. When all else properly connects & performs, what does not properly connect & perform has the issue &, hopefully, that can be repaired without having to replace it.

Do a factory reset - usually a 'secret button' hidden on the back - default router passwords can often be found on the net.

Please check out this website http://www.driversdown.com/drivers/Zonet-ZEW2505-802.11g-Wireless-USB-Adapter-Driver-Windows_79284.shtml

Have you tried Unplug Modem, remove battery, unplug wireless, Install battery in modem, plug in, wait for selftest, plug in wireless device, wait for self test, plug in computer, boot normally. If that fails Push and hold the reset button on the wireless device for 30 seconds. The Moden should have a reset as well, push and hold for 30 seconds or so. If I had the Make, Model of the Modem and Wireless device I could be more helpful.

Check out zonets website or search google for Zonet Web Camera Install Disk, download it and install.

Try the manufacturer's website.Get onlineand got to www.google.com In the google search box type: "ZonetSupport" (without the quotes and put your manufacturer name before Support). Look for downloads and drivers. Enter your model number and operatingsystem when requested. Download and install the drivers.

http://zonetusa.net/index.php/prod_download/