20 Most Recent Belkin N1 Vision Router - Page 2 Questions & Answers

Make sure that your computer is able to go online directly through the modem.
If your computer is able to go online through the modem, that means the modem is working fine.
You will need to connect the computer to the router and the modem to the router.
open the set up page of the router and change the settings of the router according to the ISP.

Click Here for more information about the routers and network

you need a wirless device to plug into the xbox 360 or u can use a long ethernet cable

Ascertain what incoming ports you need to open and the IP address of the device / computer that you wish to forward to and set the ports up manually.
· Enter a description for the service
· Enter the inbound port ranges from WAN
· Enter TCP/ UDP type
· Enter IP address that the service is to be forwarded
· Enter the private port range (keep these the same as the incoming ports unless you are running multiple services ie 2 web servers on port 80)
· Click enable check box and save entry
· Repeat as required.

The problems you are having is that 32 bit addressing will only provide a maximum volume size of 20Gb. If you can reformat, you’re NAS device as NTFS this may help.

Check the routers gateway IP address is in the same subnet as the other computers or laptop.
Ie 192.168.1.X . (X is between 1 and 254)
In addition, the sub net mask is 255.255.255.0

If all is ok then it is probably a miss configuration with WPA /WEP options

What kind of wireless Access point u using

Yes you can. Here is how to do it:

1. You have to set your Router toward the edge of your network's current range limit
2. Then you have to install and navigate to the Admin Panel of the Router (if already installed, skip the installations option). Use a browser. IP Address would be http://192.168.0.1.
3. Log in.
4. Click on the "LAN Settings" (Below "LAN Setup"). Now you have to have the Number of Devices which you are going to connect to the Network.
5. Click inside the text box for the wireless router's IP address at the center of the screen. Delete the last number in the IP address. You have to Type in a number that is AT LEAST Number of Devices + 1. Lets say you are gonna connect 50 Devices. Then the Number = 51.
6. Now go to "DHCP Settings". Click on the option button "Turn Off".
7. Click on "DNS" below the "Internet WAN" title. Click on the "Disable Forwarding" option button.
8. Click on "Security" and Scroll down until you see "Port Forwarding". Remove each IP in the Text boxes. Find the option button "Gateway" and Click on it.
9. Click on the "Application Gateway" underneath the "Firewall". Click on the box which has the Label "Disable Firewall".
10. Click Apply and Ok.
11. Log off.

• Make sure you have a Strong Password for the Router. As you can see the Security is bit not tighten.

Generally the N standard rotuer do not require any Range Extender s. However if you are trying to use Range Extender with N router. You need to use G or B/G mode mixed, also you have to change the channel from Auto (as in Linksys Router,not sure about Belkin Router) 6 or 11, So that the Wireless connection can detect the Range Extender.
If you are facing any difficulties, please let me know. It was a pleasure to assist you!
If the solution helped you to overcome the issue, please rate the answer with a testimonial.
Thanks for contacting Fixya!

Hi Friend,
There may be an issue with you router,i.e., the router may be gone bad (RMA)

Regards,
Aysaam

1.check the area where you have the router mounted.
2. Move the router to a place where there is no heat build up.
3. try blowing the router out with canned air or vacuum.

If you have a 3G phone in the house, It operates at the same frequency and is a nono.

If not I would suggest you completley rest modem and re-enter U/N, P/W etc and set up secure network also. If still a problem, maybe faulty modem.

Hi Friend,
Please check it by updating the Firmware for your router from the below website

www.belkin.com/support

Regards,
Aysaam

Hi Friend,
This may the issue because of the below,

Cause 1: Try to insert the Power plug adapter in any other wall outlet

Cause 2: Check by Resetting the Router,(Insert a Pen or Paper Clip inside the Reset hole and hold the button until the lights are getting turn off,once its goes off without taking the hand from the reset unplug the power cable from the router and plug it again after 10 sec,Now take the pen or paper clip from the reset hole)

Cause 3: Even now you are not having any solution,then the router is gone bad,you may go for a replacement

If any other clarification,please feel free to contact us

Regards,
Ayyasam

u can try dowloading the latest firmware for the n1vision router...
here is the link.... http://en-us-support.belkin.com/app/answers/detail/a_id/503/p/328
download appropriate version and save in the hard disk.... login to router page... type 192.168.2.1 in internet explorer... password leave it blank and click submit.... click update firmware on the left....select browse and update the firmware dowloaded... after updating, login to the router page again and click on restore factory defaults(must)....your problem ll be rectified....

You would have to log into the router to configure port forwarding on port 80. You would have to know the IP address of the computer hosting the website and put that in the routers config under port forwarding.

I just checked this with the folks at Belkin customer support - they do not support setups with PS3 - I am also desperately trying to get this to work.

Any ideas?

Hi Friend,
Please follow the below mentioned steps one by one

Step 1:Take a cable,connect one end to the modem and other end to the router (In the port named,Modem)

Step 2:Take another cable connect one end to the Computer at the back side and other end to the router (In any one of the port named,Wired)

Step 3:Open an Internet Explore and type 192.168.2.1

Step 4:Now you will see a belkin router Setup page

Step 5:On your left hand side you will see a menu named,Restore factory default,Click on it

Step 6:Now It will prompt you for a Login Paasowrd,You leave it blank and click on Submit

Step 7:Click on Restore Default,It will complete the process and bring it to the front page

Step 8:Now On the left hand side click on MAC Address

Step 9:Now it will prompt for a Login Password,You leave it blank and click on Submit

Step 10:On your left hand side click on Wifi protected setup (WPS)

Step 11:Change the WPS to disable and click on Apply Changes

Step 12:Unplug the power cable of both the modem and router

Step 13:After 10 secs,put the power cable only to the modem,and wait until all the lights in the modem gets litup(If all the lights doesn't got litup then please check with your Internet service Provider).After all the lights got litup,put the power cable to the Router,Check all the lights in the router will be stable

Step 14:Now check in your computer that you are able to go online in both wired ,wireless computers and in the wireless devices like IPOD,IPHONE,PSP

If you have any clarification,Please feel free to contact

Regards,
Ayyasam

I suggest you contact Belkin customer service and explain your problem. They will either walk you through the steps required to fix it, or (assuming your router is new and under warranty) replace your router with one that works properly.

Firmware 1.00.23 fixes the VPN issue on the f5d8635 series.

http://www.zath.co.uk/how-to-get-xbox-live-working-with-belkin-n-wireless-router/

Here is the manual in PDF. Hold the reset button for 20 seconds and wait for it to come back up. Then punch in the default login credentials from Belkin (the handbook will tell you how)

Good Luck!

Jesse