20 Most Recent
Maytag Dishwasher - Page 4 Questions & Answers
Maytag dishwasher error code 96?
Try killing power to the unit, typically this is at the breaker box but from time to time it may be connected to another circuit in the kitchen that may have GFCI circuit. Make sure the GFCI is not tripped killing power.
1/22/2013 4:12:50 AM •
Maytag...
•
Answered
on Jan 22, 2013
Doesn't drain out all the way water stays in
Hi
Dishwasher not draining issue usually occurs due
to kinked drain pipe, clogged drain filter or drain pump. First make sure that
the drain is not clogged and remove clogs if present. If no visible lint is
present then remove the lower front access panel to check the drain filter and
drain pump for any clogs, you'll need to clean the drain filter and drain pump
completely. Also, check for any food pieces stuck near the pump impeller &
clean the chopper assembly. Please note that dishwashers don't drain out the
complete water such that heating element doesn't overheat. Hope this helps...
Please post back for any further assistance.
Daniel
12/4/2012 7:44:33 PM •
Maytag...
•
Answered
on Dec 04, 2012
Wont turn on is thier a reset button
OK I am not an expert but I have spent the last two weeks learning about
and fixing my dishwasher! Hopefully I can save you a headache. Try the
following:* Try turning off the switch for a longer period of time - 10-15 minutes. This may reset your washer.*
If any of your button lights come on but a regular cycle will not start, try running diagnostic/reset cycles by pressing
heated dry -normal- heated dry or heated dry-sanitize-heated dry in
sequence. If the cycles run fine, you will rule out a power, latch,
motor/drying issue. It also may (hopefully) reset your system.* If
your buttons do not light up or normal function still does not resume after the reset, make sure your power (from the
breaker box) is turned off and unscrew (with a star-shaped screwdriver
bit - check your car emergency kit/toolbox, you may find you have it)
and open the front button control panel and check all connections. Try
carefully unplugging and replugging wires and look for any
corrosion/moisture on the circuit board. * If that does not work,
test the circuit board by unplugging the green ribbon cable from the
control panel, reassembling with the ribbon cable unplugged, flipping
your circuit back on and then closing the dishwasher door. If the drain
motor runs, it will show you that there is power getting into the machine and that there is still some function with the
circuit board. Although it doesn't rule out the circuit board
completely, it will point to the possibility of a control (button) panel issue
and you may try replacing that. If the drain test does NOT run, it may be the
circuit board that needs to be replaced.
There may be some additional instructions specific to your model hidden in an envelope behind the kickplate of your washer.
Hopefully some of that helps!
7/11/2012 2:51:25 PM •
Maytag...
•
Answered
on Jul 11, 2012
Washer will not start
OK I am not an expert but I have spent the last two weeks learning about
and fixing my dishwasher! Hopefully I can save you a headache. Try the
following:* Flip the switch off and on in your breaker/circuit box. May reset your washer.*
If that doesn't work, try running diagnostic/reset cycles by pressing
heated dry -normal- heated dry or heated dry-sanitize-heated dry in
sequence. If the cycles run fine, you will rule out a power, latch,
motor/drying issue. It also may (hopefully) reset your system.* If
normal function still does not resume, make sure your power (from the
breaker box) is turned off and unscrew (with a star-shaped screwdriver
bit - check your car emergency kit/toolbox, you may find you have it)
and open the front button control panel and check all connections. Try
carefully unplugging and replugging wires and look for any
corrosion/moisture on the circuit board. * If that does not work,
test the circuit board by unplugging the green ribbon cable from the
control panel, reassembling with the ribbon cable unplugged, flipping
your circuit back on and then closing the dishwasher door. If the drain
motor runs, it will show you that there is still some function with the
circuit board. Although it doesn't rule out the circuit board
completely, it will point to a most likely control (button) panel issue
and try replacing that. If the drain test does NOT run, it may be the
circuit board that needs to be replaced.There may be some additional instructions specific to your model hidden in an envelope behind the kickplate of your washer.Hopefully some of that helps!
7/11/2012 2:43:30 PM •
Maytag...
•
Answered
on Jul 11, 2012
Brand new Matytag MDB7749AWB Dishwasher
Try putting the unit into a test mode. This my clear your issues otherwise call for service.
One of two ways to do this.
In standby (no lights) Press the combination of buttons:
hi temp wash > sanitize > hi temp wash > sanitize > hi temp wash
All lights will come on and the washer will run a test cycle anywhere from 5 to 10 minutes.
If that button comb doesn't work use:
heated dry > sanitize > heated dry > sanitize > heated dry
6/30/2012 2:22:35 PM •
Maytag...
•
Answered
on Jun 30, 2012
Not finding what you are looking for?