20 Most Recent
Maytag Dishwasher - Page 2 Questions & Answers
My maytag dishwasher is leaving a white cloudy film on my dishes that won't come off!
First check your rinse aid make sure you have some in there. I have been told that too much or too little of this can cause problems with etching glass and damaging dinnerware. . I would put a cup in right side up and wash a wash as usual and take the cup out and check that water after. Make sure your using a proper soap, and hot water is getting to your dishwasher. Or has it been full and not really coming out over a long period of time?
Another possibility is it is dirty inside the dishwasher, and not draining?
7/11/2014 4:02:26 PM •
Maytag...
•
Answered
on Jul 11, 2014
How do I reset the control panel on my dishwasher?
could be wites in the door at the hinge, the microswitches in the door lick assembly, or if it is a series of flashes it could mean a code depending on your model number. Last to check is visuals on the control board for burning, or any loose wiring.
6/20/2014 12:12:59 AM •
Maytag...
•
Answered
on Jun 20, 2014
When is on 5 minits working then display showing end what is the reason
Sounds like a drain problem maybe. Also these tend to have a blinking pattern, sometimes. Or if it is just saying clean, it could mean an error of some other function not working. My guess, the drain is clogged. check to see if you can actually cancel the cycles, fill wash and then cancel it out, then check to see if it drained all the way out.
6/18/2014 5:07:10 AM •
Maytag...
•
Answered
on Jun 18, 2014
MAYTAG DISHWASHER DOES NOT STOP PUMPING
there is a float towards the front of the d.w. usually in the corner.
if its stuck in the up position this would not allow the pump to shut off
6/2/2014 3:35:36 AM •
Maytag...
•
Answered
on Jun 02, 2014
Power is to the dishwasher put it wont turn on
hello first check yor breaker make sure not tripped.
next check for lights in your panel.
perform a normal wash if no luck
next perform a service diagnostics cycle.
note sercice diags. works on Maytag MDB7600 series.
press the following keys in less than 6 secs.
HeatedDry > Normal > HeatedDry > Normal
to advance machine cycles press Start/Resume key.
blessings,
e.
5/23/2014 11:02:53 PM •
Maytag...
•
Answered
on May 23, 2014
Door seems to lost firm motion it like a sprinf broke?
take off bottom front kick panel and u will see the door springs one on each side. check and make sure they are connected to the cable that opens and closes the door. Look at the springs closely as they could be weak.replace if need be. u can go on line to applianceparts.com to find new springs
4/11/2014 2:05:56 AM •
Maytag...
•
Answered
on Apr 11, 2014
Clean light blink, dishwasher not working
Does it blink 7 times pause then repeat if so then have a heating problem control does not detect a temperature rise, don't know your technical expertise I ohm out heater at the control easier than pulling out the machine just look for continuity means heater is good if none you'll have to reach under unit to make sure you do not have a burned wire to heater if heater is good ohm out thermistor at room temp should be between 50-70 thousand ohms very seldom does this part go bad but i had one so check it last if both parts check good then the electronic control is not outputting 120VAC to the heater.
2/9/2014 4:31:46 PM •
Maytag...
•
Answered
on Feb 09, 2014
Thermostat tripping
I just fixed my Maytag's bi-metal switch. I smacked it with the plastic end of a screwdriver. Problem solved. You may have venting issues in the dishwasher if it's continually overheating.
2/9/2014 2:40:14 PM •
Maytag...
•
Answered
on Feb 09, 2014
Not finding what you are looking for?