20 Most Recent Onkyo TX-SR605 Receiver - Page 9 Questions & Answers


easiest fix is to take all hdmi straight to tv. then come out of tv with optical cable to your receiver. that way what ever your watching will automatically be sent to the receiver thru optical. you even will get dolby dig. also you can have audio from your tv when you dont want to use your surround. keeps receiver on one input also.

Onkyo TX-SR605... | Answered on Jul 02, 2009


Check the settings on your cable box for "Audio" settings and check the output. Should be set to "Dolby Digital" If you need more help, post a comment with the make and model of your cable box and I can walk you thru setup. Hope this helps

Onkyo TX-SR605... | Answered on Jul 01, 2009


some surround sounds do not put out loud sounds except from the front speakers only. Try using different inputs to see if it makes a difference.

Onkyo TX-SR605... | Answered on Jun 17, 2009


The HDMI version in your receiver is 1.1 or 1.2 which will not pass video as it should. It's not Onkyo's firmware at issue, it's HDMI and in all receivers up to 2008 model year this is a very heated problem! The only fix is to run FIOS directly to the TV via HDMI and run it's audio to your receiver with Digital Coaxial or Optical. Hope this helps

Onkyo TX-SR605... | Answered on Jun 11, 2009


Normal 0 false false false MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;} With the unit unplugged, remove the top cover and use an ohmeter to check the 10 power transistors on the large heat sink; Q6050 thru 54 and Q6060 thru 64. If you find blown transistors (R<1 ohm from E to C) you'll need to replace them. After removing the shorted transistors, also check the associated large ceramic current sharing resistors, R6100 thru 04 next to the output transistors. These are dual 0.22 ohm, 2W resistors that typically fail open if overstressed. These are both common failures resulting from overloading the speaker outputs that will cause the proctection circuit to shut down the power supply at turn on. Good luck.

Onkyo TX-SR605... | Answered on May 07, 2009


on your directv box, go to menu, setup, setup again, then audio, then dolby digital on the right and turn it on. assuming you have an optical audio cable from your sat box to your onkyo.

Onkyo TX-SR605... | Answered on Apr 27, 2009


Shorted speakers can cause the unit going on protection mode (the red light blinking) when a certain volume is reached.

Test with a set of replacement speakers.

If it is not the speakers, it is probably transistors in the amp final or something nearby. Test also input output board.

Onkyo TX-SR605... | Answered on Apr 27, 2009


Its possible that the Receiver is going into protection mode and possible some speaker cable might have touched the body or with each other.
Remove all inputs and outputs and then restart the receiver. If it starts then you are lucky. Connect all cable and wiring properly and ensure that they do not touch each other. You might have to reset the microprocessor if the recevier has got.

If the problem persist then let me know to further the trobleshooting.

Please do rate this solution and thanks for using FixYa.

Onkyo TX-SR605... | Answered on Apr 26, 2009


I wrote most of this for a different receiver, but if you account for minor differences to your receiver this will work just fine.

There's good news and bad news. The bad news you need a separate amp because a multichannel receiver with Bose 901's attached as recommended for a standard stereo receiver will only sound right in STEREO on stereo analog material. The other speakers around the room are not designed to receive its Active Equalization and if you engage your Tape Monitor you will NOT BE ABLE TO HEAR DIGITAL sources at all. Tape Monitor is for analog stereo material only and on modern AV receivers it disables any digital inputs so you really can't use the Tape Monitor circuit or attached devices for modern digital sources. However, you can still employ the various DSP options to spread 2-channel analog source material around the room. I do.

The good news. I have a setup similar to what you want to do and it works great!

A separate stereo amp for the 901's was my solution. I run a Carver AV-406 (5-channel amp) for my 901's in Front, 2 Subwoofers and the Rear Surround channel, with the Active EQ between the receiver Front L&R Outputs and the 901's amp channels. My receiver controls everything and just drives the Center and Surround speakers.

You could get by with just a stereo amp for the 901's. A Carver M-200 is a good efficient amplifier that would have you cooking just fine (2x100W). Run it with the Active EQ between the receiver Front L&R Pre-Outputs ** and the 901's amp channels.

** Front Pre Out (or one of your analog Tape Outs) >>> Bose EQ Amplifer IN, then
Bose EQ Amplier OUT >>> new amplifier IN.


Attach the 901's to the new amp, set its volume to Max and run through your receiver's speaker level setup.

Write off the Tape Out as an input if you use it to extract the Front L&R channels. DO NOT monitor it or you'll chop the 901's out of the signal path AND kill any digital source audio in the receiver.

Onkyo TX-SR605... | Answered on Apr 25, 2009


are you using HDMI cables or component. First I would try unplugging the composite and component video cables while the receiver is off. Plug them back in and turn it back on. If that does'nt work try setting the receiver to factory default and redo the settings. You can find how to reset to default in your user manual.

Onkyo TX-SR605... | Answered on Apr 24, 2009


try checking the fuses, it shouldnt shut off after 5 to 15 seconds this is the 1st time ever hearing about that try that an let me kno wut happens
hopfully that can give it a go

Onkyo TX-SR605... | Answered on Apr 21, 2009


Probably an output transistor issue, it will need to be serviced by a professional, especially if it turns off immediatly after you turn it on

Onkyo TX-SR605... | Answered on Apr 07, 2009


Dear Bzambo,

The batteries on the remote are fresh? if so the remote might be bad.

Sidlahora

Onkyo TX-SR605... | Answered on Apr 01, 2009


bought an new one for $5.

Onkyo TX-SR605... | Answered on Mar 17, 2009


Your receiver is basically going into protect mode.

The SR 605 contains a microcomputer for signal processing and control functions. In an unlikely event, it may cause it to lock up. Unplug the power cord from the wall outlet, wait for 10 to15 seconds and then plug it back again.

Please also check your speaker cabling again. Make sure that all of them are seated properly, none is touching each other or the body of receiver. Take out all the wire and put them back again if necessary..
Some times even a little tiny frayed wire touching the receiver could trigger the protect mode. Be careful, since protect mode is sometimes not fast enough and it could blown a few trasistors in the power circuit.
Just check your speaker as well....whether they play all right thru another receiver or amplifier. its posiible they might be shorting inside. A little frayed wire could also trigger the protect circuit in your receiver.
I hope this should solve your problem. If you still can’t resolve the issue yourself, try resetting
the AV receiver/AV amplifier before going on to opening the Receiver.
To reset the Receiver to its factory defaults, turn it on and, while holding the [VCR/DVR] button, press the [STANDBY/ON] button. "Clear" will appear on the display and the Receiver will enter Standby mode. (note that resetting your receiver will delete your custom settings as well as your radio presets).

If everything else seems all right and still your receiver shut down when you raise the volume then it possible that there are bad connections on the main board that are set in.

This would generally happen if the system is slighly old or have dry solder and when you raise up the volume. This should be a simple repair that will not require parts. If you can solder, you will be able to repair this yourself. If not, then a local service center will change the local labor rate.

Hope you can sort out your problem with the above trouble shooting. Let me know if I can guide you further.
Best of luck. Thanks for using FixYa!

Onkyo TX-SR605... | Answered on Mar 13, 2009


yes here is the manual for it.
http://63.148.251.135/redirect_service.cfm?type=own_manuals&file=SKW204_En.pdf

now you will see this picture on page 5
768816d.jpg now where it says 6 this is your line input. Now you will plug in a subwoofer cable to this and on back of your receiver to the subwoofer output. and you now must enable the subwoofer option in the setup menu of receiver i think it would be under speaker configuration.


so the answer is yes it would.

Onkyo TX-SR605... | Answered on Mar 01, 2009


yes here is the manual for it.
http://63.148.251.135/redirect_service.cfm?type=own_manuals&file=SKW204_En.pdf

now you will see this picture on page 5
768816d.jpg now where it says 6 this is your line input. Now you will plug in a subwoofer cable to this and on back of your receiver to the subwoofer output. and you now must enable the subwoofer option in the setup menu of receiver i think it would be under speaker configuration.

Onkyo TX-SR605... | Answered on Mar 01, 2009

Not finding what you are looking for?
Onkyo TX-SR605 Receiver Logo

334 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Onkyo Audio Players & Recorders Experts

Ted28

Level 1 Expert

5 Answers

 Grubhead
Grubhead

Level 3 Expert

5699 Answers

The Knight
The Knight

Level 3 Expert

76140 Answers

Are you an Onkyo Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Onkyo Audio Players & Recorders

  • Onkyo Audio Players & Recorders

Most Popular Question

onkyo tx sr605 system zone 2 used work

  • Audio Players & Recorders
Loading...