20 Most Recent Sony STR-DG510 Receiver - Page 4 Questions & Answers

The word UNLOCK may appear in the display if there is a problem receiving a digital audio signal. Follow the steps below to troubleshoot this issue.

1. Ensure the correct input is selected to receive the Audio/Video (A/V) from the appropriate source.
2. Ensure a digital cable is connected to appropriate DIGITAL jack.
3. Ensure the other end of the digital cable is properly connected to the A/V source.
4. Ensure the A/V source is set appropriately to output a digital signal.
NOTE: The A/V source may have a DTS setting that needs to be turned on, or a DPCM setting that needs to be set toDolby Digital .

error 12 is when you autocalibrate and do not have the microphone connected, when that is the case the receiver can not detect the speakers.

For this Sony, you have to use separate audio cable(s). Either optical in BD or Digital Audio in DVD (single coaxial cable will do the trick) I bet the display says UNLOCK. I had the same problem, very dumb.

Good day!

error 12 is what you get if you autocalibrate and do not have the microphone attached.

The word UNLOCK may appear in the display if there is a problem receiving a digital audio signal. Follow the steps below to troubleshoot this issue.

1. Ensure the correct input is selected to receive the Audio/Video (A/V) from the appropriate source.
2. Ensure a digital cable is connected to appropriate DIGITAL jack.
3. Ensure the other end of the digital cable is properly connected to the A/V source.
4. Ensure the A/V source is set appropriately to output a digital signal.
NOTE: The A/V source may have a DTS setting that needs to be turned on, or a DPCM setting that needs to be set toDolby Digital .

Remember the rear speakers are called surround... Did you select surround on the unit? if it says stereo then you will only get fronts, select surround to get the rest.

You have to use the same connection in and out. You can not mix inputs and outputs (Example- HDMI IN will not play on Component out and Vice Versa.)

Hi, i also have a conia plasma (and sony 510 amp). Which video connection are you using? DVI-VGA? DVI-component? Note that the tv probably defaults to using YPBR rather than VGA so you may need to play with settings in the menu ...

I think you have to run a separate audio line from the dvd to the 510, because the HDMI is only passive

call sony for warranty repair. there is an internal problem most likely one of the amplifiers has shorted and is in protect mode.

Hi 1prosource

I concur:) Glad you got it sorted out. Any other dramas you may have, just give me a hoy :)

regards
robotek

On Page 54/55 of user man. has a step by step instructions.

Sounds like damaged channel in output circuitry. Take to pro/tech

The easiest way is to connect to one of the tape out jacks. These should be live for all inputs.
Dan

Make sure that these inputs are enabled. I'd have to confirm within the manual, but I believe that these have the HDMI section disabled by default.
Dan

Try, the fusível, if not work, try off the outlet 2 minutes, and plug in wall again.
-Verify the Voltage Selector too.
If after does not work, you need a techinical assistence.

What port do you have the HDMI from you BD player into on the 510. If you have it on the DVD port then fiber optic will do you no good, the DVD HDMI only supports digital coax, the Video2 HDMI only accepts fiber optic, and there is an extra fiber optic for the Sat input. If your BD player does not have digital coax out, or if you dont want to buy another cable, just move the HDMI from DVD to Video2 on the 510. I am willing to bet you have the BD player plugged into the DVD HDMI port and the fiber optic cable from you BD player to the Video2 fiber input.

cant use both hdmi and opti outs try sum setting in blue ray but u nee dto plug all blue ray dish directto samsung hdmi then 1 master digital out form tv to sterio digital i n ok tell samsung your output also

please explain in better detail.

check the volume output from your components, and make sure they are not set too low