Polycom SoundPoint IP 550 IP Phone - Page 8 - Answered Questions & Fixed issues
Ecco TV 32 D-LED it just stuck on USB Mode,the source button is not working and i don't have a remote.Help
Hello,
If your Ecco TV 32 D-LED is stuck in USB mode and the source button is not working, and you don't have a remote, there are a few things you can try to resolve the issue:
- Power cycle the TV: Unplug the TV from the power source and leave it unplugged for a few minutes. Then, plug it back in and turn it on. This can sometimes reset the TV and resolve minor software glitches.
- Try using the buttons on the TV: Although you mentioned that the source button is not working, try pressing other buttons on the TV itself, such as the menu or volume buttons. Some TVs have different combinations of buttons that can act as a substitute for the source button. Refer to your TV's user manual if you're unsure about the button combinations.
- Check for a physical source button: Look closely at the TV's physical buttons to see if there is a dedicated source button or a button with an icon indicating input selection. Pressing this button should allow you to cycle through different input sources, including USB mode.
- Borrow a universal remote: If you don't have the original remote for your TV, try borrowing a universal remote from a friend or neighbor. Universal remotes can often be programmed to work with different TV models. Check the remote's instructions or manual on how to program it for your TV brand and model.
- Contact the manufacturer: If none of the above steps work, it's recommended to reach out to the manufacturer's customer support. They can provide you with specific information tailored to your TV model and help troubleshoot the issue further.
1/6/2024 7:56:16 AM •
Computers &...
•
Answered
on Jan 06, 2024
•
339 views
Dragonhawk tattoo gun
Friend had this same issue, here's how I fixed it, and hopefully it'll work for you (and anyone else with this issue.)
First is the copper screw thing at the top of the gun. It needs to be just barely touching the flexible metal bar below it. It's very finicky; the distance between too far away and touching it too much is very Very small. At the proper distance, it should hum and/or spark. Large sparks are normal when it's brand new; they'll disappear pretty quick though, so don't worry if it happens.
If it's humming and sparking properly but the needle isn't moving, it's probably that the needle guide (holder? nib? The translucent green part whatever it's called) could be too high up, causing the needle itself to get stuck and not have room to move up and down. Simply loosen the screw that holds the nib in place, lower it until the needle is only slightly exposed, and tighten the screw again.
It worked for my friends gun, so hopefully it'll work for yours too.
images are the full gun, close up of the copper screw thing, close up of the nib/needle, and diagram attempting to explain the nib distance a little bit more.
1/3/2024 6:59:10 AM •
Computers &...
•
Answered
on Jan 03, 2024
•
360 views
Battery discharged, not charging
No details given, but let's guess a laptop because you are in the category 'Computers and Internet'.
All questions need 'make model (what it is)' as first 3 words please.
Power down the computer
Remove the battery
Run the computer on mains power
Close down the computer
Unplug from the mains
Press and HOLD the Power button for a FULL 2 minutes.
Insert the battery, plug into the mains and power on.
If that doesn't fix it, you need a digital multimeter to check the battery charger unit is providing voltage at the connector plug, typically 11.1 volts or 14.8 volts, to as much as 19 volts.
Another possibility is that the power connection port has dry joints or damage to the motherboard connector through constant use.
..
12/31/2023 6:30:42 AM •
Computers &...
•
Answered
on Dec 31, 2023
•
31 views
Not finding what you are looking for?