KitchenAid Microwave Convection Oven - Answered Questions & Fixed issues

common problem with lots of MWs - the door switches are not set and secured properly. Now they are totally off. Need to pull apart and reset. Not a task for an average homeowner. Mine (Whirlpool) did that 1 week after I got it - exchanged for a new one.

The door switches are the problem. Well, actually one of them is. when you open and close the door make sure the switches are actually being engaged. I have seen the plastic snaps that hold them broken and the switch just moves. Just replace all three switches and you will be fine.

That may be called the turntable coupler or turntable support or roller ring assembly.You can find helpful exploded views and part numbers at the link below, by replacing XXX with the full model number found on the tag on your microwave (not on the service manual). XXX&siteCd=WHRCOM&userType=Consumer">http://shared.whirlpoolcorp.com/product_literature/search_results.jsp?searchTerm=XXX&siteCd=WHRCOM&userType=ConsumerMy preferred place to order Whirlpool parts is from the Pro here.

try with www.fitness.manualsonline.com + www.retrevo.comGod bless you

well i will give you a link to suggestions that have already been made by other experts on Fixya. click here
otherwise,

A. Unplug oven or disconnect power.

B. Open the back panels and make sure the P6 and P2 connectors are fully

inserted on the appliance manager and on the lower oven user interface board.

- If they are not plugged in, plug in connectors and go to step F.

- If they are plugged in, go to step C.

C. Visually inspect all wires between P6 on the appliance manager and P2 on the

lower user interface.

- Make sure wires are not cut or pinched.

- If the wires appear to be intact, perform a continuity check between

P6-1 of the appliance manager and P2-1 of the user interface board.

Hi,

Here is a tip that will help you to figure out what is wrong with your Microwave Oven....

Basic Microwave Oven Troubleshooting Tips

heatman101

[\[\[\[\[\[\[\[\[\[\[\[\

If this is the flip down door. You will need to take apart the side cover of the unit to fasten the spring. Once you have done that you need to put a pen or something to hook it so it doesn't drop down in the unit. If you are unable to hook the spring in the door. You must take the outer cover off the door to hook the spring and then replace the cover. You may find this to be a two person job and may be easier to hook the door before you hook the unit. Some doors are different then others.

chk the door switch also chk the input supply to the control board and smoothing capacitors

May I get the make and model # to help you more

I cannot determine from your description what part it is you exactly need.
This is a link to Sears Parts and you make and model
Look through the diagrams.
As for price and delivery... that's up to Sears
Good luck!

http://www.searspartsdirect.com/partsdirect/part-model/Kitchenaid-Parts/Microwave-Parts/Model-YKHMS1850SS0/0593/0123370?searchedModel=YKHMS1850SS&blt=

You can get the handel on the link below. Part 13.

http://www.appliancepartspros.com/partsearch/model.aspx?model_id=5139000&diagram_id=28286757#d28286757

Good Luck

That would be a broken door spring, and it's best to replace them in pairs.

On some models, this can be a difficult job.

You can find helpful exploded view diagrams and order parts by entering your full model number here.

Good luck.

We're happy to help you with free advice and we'd appreciate your thoughtful rating of our answer.

Hi,
It sounds like the door interlock is broken.
Have a look for any hooks or latches that may have snapped.
If the door interlock is faulty - do not use this microwave untill a replacement is ordered and fitted.

Hi. this code represents a key pad or control board malfunction. you will have to make sure the key pad or control panel connectors are connected tightly and securely. If the wires and connectors are secure, the actual control board may be faulty and you will need to replace it at this point.

Doors for microwave ovens are usually replaced as a complete item. I would ask the person who forgot to fix the door latches properly back to fix it properly. If some of the clips were snapped off when removing the door panel, the panel must be replaced or it will fall out again.

I am a bit late on this question, but just ended up in a rabbit hole of unanswered Kitchenaid questions The self cleaning features only serves to keep manufacturers in steady sales of parts. Quite simply the oven can only take those temperatures a few times until they break. The heat burns out elements, damages fans, door locks and worst of all damages control boards which are not far enough from the heat source. You problem sounds like the walls of the oven have buckled in the heat so the racks no longer fit. Too late now, but you should have taken Kitchenaid to court, the oven was not fit for purpose under the description they used to sell it to you. Never use the self cleaning feature as stated here https://www.google.com/search?q=self-cleaning+oven+temperature Never Ever use the self clean feature. We see damage here every couple of weeks. The worst was a burned control board on an oven that all parts were obsolete, so the self clean cost a thousand bucks! Self-cleaning ovens bring the heat so you don't have to spend hours scrubbing. Traditional self-cleaning cycles heat the oven between 800°F and 900°F, helping turn soil and spills to a powdery ash you can then wipe away. They utilize only heat-no chemicals-and are built to withstand high temperatures. (Says Maytag who love selling elements, door locks and other parts),

Why You should Never Run A Self Clean Oven Cycle & ...

General Appliance Servicehttps://www.generalappliancesvc.com > why-you-shou... Jan 29, 2020 - A self-cleaning oven is a feature on many modern ovens that burns off cooking spills and splatters with an extremely high temperature (932 F° or ...

Self-cleaning oven

Wikipediahttps://en.wikipedia.org > wiki > Self-cleaning_oven A self-cleaning or pyrolytic oven is an oven which uses high temperature (approximately 932 °F (500 °C)) to burn off leftovers from baking, without the use ... ‎Pyrolytic process · ‎Alternative technologies · ‎Catalytic cleaning

Self-Cleaning Oven: 6 Reasons to Stop Using Feature ...

FIX Appliances CAhttps://fixappliances.ca > 4-reasons-stop-using-self-cle... A self-cleaning oven is a feature on many modern ovens that burns off cooking spills and splatters at an extremely high temperature (932 F° or 500 C°) to aid in ... ‎How Self-Cleaning Ovens Work · ‎Major Parts Damage ..

Yes it should do, but they are very dangerous to work on. https://www.google.com/search?q=Kitchenaid+microwave+f4+error https://www.fixya.com/support/r29874712-repairing_microwave_ovens ..

Open the control panel using this diagram Official KitchenAid KEMC377KSS05 wall oven/microwave combo parts ' Sears PartsDirect Check the cables and connectors. If Ok then problem is in cuicuit board.

I'm not familiar with that particular model, but with many of their models (and many other manufacturer models as well), unfortunately the beep cannot be turned off.

Question moved from Cars and Trucks category. No wiring schematic exists, but this does show there is an internal fuse. https://www.repairclinic.com/ProductDetail/2145587 Service manuals aren't generally available, because the insides are so dangerous! Keep away from the step up transformer and capacitor with 120,000 volts stored in it. https://www.google.com/search?q=kitchenaid+kmhs120ess+service+manual& https://www.google.com/search?q=kitchenaid+kmhs120ess+wiring+diagram&rlz=1C1QJDB_enCA643CA644&sxsrf=APq-WBu2IViisg_YzIUbx0IaRs0iQu4SNw:1648409430308&source=lnms&tbm=isch&sa=X&ved=2ahUKEwiDuqbUg-f2AhUaac0KHd1pAb8Q_AUoAnoECAEQBA&biw=1920&bih=937&dpr=1 ..