20 Most Recent Memorex MT201224 20" TV - Page 8 Questions & Answers

Hi,
The issue you describe is consistent with a power supply board issue. This is the board where the AC goes to. This problem may have occurred as a result of irregular power supply, or excess power supply or power surge.....
The TV is receiving current but cannot circulate or transfer the current to other necessary part of the TV because of the defective power supply board. You might be lucky it's just a blow fuse. Also a defective transformer can cause your TV not to power on.
All these can be checked on the power supply board.
But more often bad capacitors causes problem on the power supply board. I do not think the power board needs replacement, rather those defective capacitors is causing this issue. Open unit up and take a look at the power supply board.You will probably see one or more electrolytic filter capacitors that are bulged up in the top-not perfectly flat like the others.
The value of these capacitors will be different, most likely they will be somewhere around-820 to 2200uF/25 V( or /10V sometimes) . You can replace them with same values but I would recommend the voltage rating to be higher(like 35V for an original 25V) for reliability purposes.
What happens is,these bulged top capacitors will cause a low and unfiltered DC voltage=main board will malfunction(the relay will keep clicking until the caps are holding enough charge to bring the voltage up over a threshold point).
You can buy these capacitors at any Fry's or Radioshack store or you can order them online at vendors like "mcmelectronics.com"(look for electrolytic capacitors). After replacing these capacitor(capacitors) most likely the normal operation will be restored. Or you can by a refurbished complete power board to save you some stress.
Note: There may be also some other causes for this symptom ,like a defective T con board ,or main board,but the bulged top capacitors are the most common cause for this issue.
If you don't know about TV repairers, take the TV to the nearest repairman to fix the fault for you. Also, note that TV stores a lot of current, so wait a while before opening the TV back cover.
I hope this helps.
Good luck.

Try on e-bay, best regard's.

Hello
Memorex Tv codes with GE-RM-24961 model remote control are:
.000 001 004 009 049 051 135
OK.

Usually, if you push the Channel button beyond the number of channels you have, it will proceed through the Active Inputs, or Aux 1 and 2. If not, you may want to check if your TV has a Source or Input button on it. Else, check the Menu for Input selections.

Last but not least, get a remote if none of the above help. I’m happy to help further over the phone at https://www.6ya.com/expert/jeremy_69f3cc28d95bf514

My Memorex Blue Ray MVBD2520 keeps doing a 1 second freeze when playing regular DVD's....Does anyone know how to fix this problem?

check if the problem is not in the TV or try a disc cleaner, the dvd room might be dirty. hope this help you resolve your problem.

Your LCD lamp may have burnt out or the component usually a driver transistor that drives the lamp to glow may have been defective. Some of LCD have fuses on this section that automatically opens when there was a problem. A qualified electronic service technician could figure out your problem right away if you don't have any experience in electronics troubleshooting.

unless you know how to open a plat panel tv you can check the fuse if it's busted or is it your tv is 110v and somebody plug it to 220v the fuse busted first then some parts maybe affected too

The magnetic reader has been damaged and needs to be replaced

Hi
Please intimate model number of tv to find out user manual copy for you, serial number wont help.
Thanks.

I had this exact same problem after setting this model DVD player up. I put in a disc thinking I would listen to the movie while working on some other projects and would call tech support in the AM.

Putting in the disc fixed the problem. If there is a disc in the system, I do not have this issue. If thee is not, it does the same thing while it is on.

can't set timer, because i can only set on ch. 3. what if i want to record ch. 72?

Please try with the following codes: 000, 001, 004, 009, 031, 046, 049, 051, 135, 268, 310.

No,the DVD player build in tv can't record,only play DVD Disc only.Want to record personal VHS tapes only to DVD Discs,must have a seperate device unit VCR/DVD RECORDER device player not a device unit VCR/DVD PLAYER.Connected to the tv record VHS tapes to DVD Discs.

it is a diagnoses jack. Used by factory tech to diagnose repairs.
please leave feedback

hi,
In your tv the closed caption option is in on position.
go to the menu and surf for the closed caption option (CC) and select it to OFF mode.
the black squire will disappear.
ok

There is a reset button on the right side (as you hold it looking at the screen) You need a pin to push it. Be careful, there is a microphone on the exact opposite side that is the exact same size.