Top 20 Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum Questions & Answers

There is probably more gunk in there, the gunk can dry and break off in little shards which can get clogged up. You can try putting straight vinegar in it, try running it through and let it sit in there for a while to see if it can help loosen up and flush out the gunk.

http://www.pc4cracked.com/2017/07/vegas-pro-14-build-270-crack

Hello, this is Ava with Think Crucial. First, water tank and formula tank should be filled correctly. Second, make sure the tank is seated properly and reprime the pump. Lastly, make sure that the caps are on securely and the red rubber auto-load gaskets are in place. If the red auto-load gasket is missing, check to see if it's stuck in the reservoir and place it back at the bottom of the tank outlet connection. You can purchase a wide variety of high quality Bissell replacement parts for your Bissell vacuum direct from Think Crucial with free shipping and an exclusive 10% coupon for Fixya.com readers, use code: FIXYA10 http://www.thinkcrucial.com/search?type=product&q=bissell I hope this was helpful. Ava B. Think Crucial Customer Care http://www.thinkcrucial.com/

Then check out the plumbing and mechanism responsible for the spraying of the water. Trace it out.

Check the hose (vacuum hose) to the head of the vacuum, it may be split or has come of.

If you look at the location where the tank connects to the base, there is a socket, in that socket is a one way rubber flap. That flap sticks and wont open to allow cleaner into the pump. I used a small screwdriver to press that flap out of the way

Hello, this is Ava with Think Crucial. First, make sure that the caps are on securely and the red rubber auto-load gaskets are in place. If the red rubber auto-load gasket is missing, check to see if it's stuck in the reservoir. Next, check the tanks for cracks or damage. If there is damage then you may need to replace it. If your gaskets are correctly assembled and your tanks don't seem to be damaged, at this point it might be best to take your carpet cleaner to a technician. You can call Bissell at 1-800-237-7691 for authorize service center near your area. You can purchase a wide variety of high quality Bissell replacement parts for your Bissell vacuum direct from Think Crucial with free shipping and an exclusive 10% coupon for Fixya.com readers, use code: FIXYA10 http://www.thinkcrucial.com/search?type=product&q=bissell Ava B. Think Crucial Customer Care http://www.thinkcrucial.com/

Hello, this is Ava with Think Crucial. Make sure that you have BISSELL 2X Formula and water in your clean water tank. Check as well if the spray tip on the CleanShot has a clog. If it is clogged, clean the spray tip with an object such as a paperclip. If CleanShot itself has been damaged, it needs to be replaced. If your CleanShot has a button,, check to make sure you are pushing down the button on the upper handle. If you are pressing the button, make sure the handle is securely attached to the body of the machine. You can purchase a wide variety of high quality Bissell replacement parts for your Bissell vacuum direct from Think Crucial with free shipping and an exclusive 10% coupon for Fixya.com readers, use code: FIXYA10. http://www.thinkcrucial.com/search?type=product&q=bissell I hope this was helpful. Ava B. Think Crucial Customer Care http://www.thinkcrucial.com/

Hello, this is Ava with Think Crucial. First, make sure that the caps are on securely and the red rubber auto-load gaskets are in place. If the red rubber auto-load gasket is missing, check to see if it's stuck in the reservoir. Next, check the tanks for cracks or damage. If there is damage then you may need to replace it. If your gaskets are correctly assembled and your tanks don't seem to be damaged, at this point it might be best to take your carpet cleaner to a technician. You can call Bissell at 1-800-237-7691 for authorize service center near your area. You can purchase a wide variety of high quality Bissell replacement parts for your Bissell vacuum direct from Think Crucial with free shipping and an exclusive 10% coupon for Fixya.com readers, use code: FIXYA10 http://www.thinkcrucial.com/search?type=product&q=bissell I hope this was helpful. Ava B. Think Crucial Customer Care http://www.thinkcrucial.com/

Simple answer: YES Anytime you are sampooing anything the under surface will be exposed to the cleaner. Move throw rugs to a location safe for the cleaner. Kitchen floors are usually good for this or a concrete floor. Remember to let carpet dry completely before replacing it. It will be lighter when dry so easier to move. But as a glass on a wood side table leaving a ring a wet carpet can leave a shaped stain.

Contact Costumer Care 1-800-237-7691

First locate screw pack (you will need a Phillips screwdriver). 2 long Phillips screws with hex nuts, 2 short Phillips screws. Should be taped to under part of handle. 2, Put upper handle into lower handle. 3, feed the power cord through the tool caddy from the flat side. Place caddy to handle so the hex shaped holes on upper portion. 4. Place the hex nut in the hex shaped hole and insert long bolt through the front of the handle. Do the same on the other screw and tighten them snuggly. Be careful not to over tighten them. 5. Insert small screws into lower 2 holes through the back side of the lower hose rack. Turn until tightened. 6. Attach tool(s) (that would be a small brush or the pet brush attachment to end of hose and on the attachment holder on front of upper handle. 7. Wrap hose around large holder closest to handle and power cord is wrapped around outer holder with rotating clamp. Hope that helped

See page 20 of the manual (linked below) for troubleshooting - and likely page19 to learn how to replace the belt. Download manual Purchase replacement belt(s) Bissell 9500 ProHeat Google Search

you can download the manual off the link below http://www.bisselldirect.co.uk/user-guides

Hello, this is Ava with Think Crucial. There are a number of reasons why your unit doesn't spray water. It could be that the !) water tank is empty which you can fill heavy duty bladder with hot tap water. 2) If Formula tank is empty, you can fill it with Bissell 2x formula for cleaning. 3) If tank may not be seated properly, turn the power off, remove and reseat the tank. 4) If pump may have lost prime, try to turn off and then turn on the unit, wait for one minute and depress trigger. If still nothing happens, I suggest you contact Bissell 1-800-237-7691 for further assistance. I would like to let you know that you can order replacement parts for your vacuum needs. Please visit our website http://www.thinkcrucial.com/search?type=product&q=bissell As a special offer here is an exclusive 10% coupon for Fixya.com readers, use code: FIXYA10 Ava B. Think Crucial Customer Care http://www.thinkcrucial.com/

Try cleaning the Flow Indicator Filter. Turn the Flow Indicator Cap counter-clockwise to remove, lift rotor and filter. Clean filter and replace in reverse order. Bissell's Consumer Care # 1-800-237-7691

It sounds like the belts need adjusting. The instructions that came with the belts should explain how to adjust the belt tension. Additionally check for debris around the brushes. This may be the reason for the belts breaking to begin with. Without the belts on the brushes should turn freely by hand. If that doesn't do you can call Consumer Care 1-800-237-7691. Hope that helps.

https://www.youtube.com/watch?v=t6lDhj7EgmM

I'd clean the small filters. One under the Flow Indicator: Unscrew the Flow Indicator cap to remove it. Lift out the rotor and the filter is directly under it. Lift the filter out and clean. Replace in the reverse order. If that didn't work then call Consumer Care 1-800-237-7691. Hope that Helped.

normally this cause most by dust inside change filter and clean it all