20 Most Recent Frigidaire FGB24S5A Gas Single Oven - Page 5 Questions & Answers

check ignitor oven if shorted, replace it. or the ignitor safety valve see if the harness wire is broken or burnt. replace it.
let me know if you try these component.

To replace the door glass do the following:

0 Check if there is a hinge stop bracket located at the hinge point of entry on the oven, in that case remove it.
1 remove the oven door by pulling it up and removing from the the hinges. If glass is broken , then secure glass with tape. Have a table with a cloth on top ready to lay the door.
2 Remove the outer screws , starting from lower side of the panel.
3Removethe inner screws. Keep all set of screws ordered, and take note of theorder you remove them. You will follow reverse order in reassembly.
4 the frame will be free now,
5 Remove the external glass panel and leave it in a safe place.
6 Replace the inner glass.
7 Clean outer glass and metal door, re-assemble it and mount it back

I also report testimonials for your model:

"removed the door from the oven by releasing clips attached to the door hinge -- very nicely engineered. Removed about 6 philips head screws to allow the door assembly to be taken apart for access to the glass. Lifted out the broken glass, cleaned the inside of the door, installed the new glass, reassembled the door (a two minute project), and reattached the door to the oven. Cleaning the inside of the door"

"I removed the oven door by lifting it off with the hinges. Disassembled the door parts one at time making sure I remember where I removed the screws until I am able to get to the broken glass. The most difficult part is making sure that the insulation strip & the gasket stayed in place after I replaced the broken glass & doing the reverse process of installing the parts together. Relatively easy process as long as you remember where the parts go. When in doubt, I had to refer to the pictorial of the disassembled door shown on your website. "

See diagram below , click on picture to enlarge:



Part here: Inner Door Glass

There is no re-settable fuse in the range.
Sounds like you need a new clock control.You can buy it and DIY for about $150.

Unplug the unit, change the igniter maybe it does not draw enough ampage.
or check the gas control knob if somebody mistakenly turned it to off position. the ON position should be inline with the gas pipe.

What you are smelling is the protective grease against rust or corrosion that came originally with your oven. the odor is normal if you are just purchase the oven.

Yes, that is the probe that sends info to the controller.

If it's not bad, then the controller is, but normally it's the probe.

Check that the controller has not been incorrectly calibrated before you change the probe out, although most do not allow a swing of more than 15-20 degrees. Yours may allow more though.

I am guessing you measured the actual temperature, to the set point temperature, with a know good thermometer.

check out properly that its not getting leaked from its pump or the valve.if that gets loose it may leak.

Go on line to westing house.com and look up your model, go to the help page and ask for their assistance, gas is not something to fool around with, I suspect it is the orifice that have not been converted to propane, I had a similar problenm with the stove top burners, and the orifices needed to be changed to (converted ) to run on propane gas.Some times manufactures send the converter orfices but most of the time you have to ask for them if you are running on propane, most stoves are set up for natural gas not propane.Most of the time the store clerks don't ask you if you will be running on propane , you have to tell them and the professional who installs the unit needs to install the orifices. Please be careful! If you installed the stove your self, you need to contact a professional installer to correctly adjust these .

Your advice was excellent, thank you.

Here is the wat to do it the right way according to the manual look at page 9 it will tell you.
ftp://ftp.electrolux-na.com/ProdInfo_PDF/Lassomption/318201551.pdf
Good Luck

Error code F93 means the lock motor assembly spent too much time to lock. Someone needs to read the continuity of the lock switches and the door switch and apply 120 volts ac to the lock motor to see if it will run. If the oven is less than 1 year old you should schedule service and let a technician diagnose and repair the problem. If you want to repair the oven yourself make the checks with a volt/ohm meter and send another email if you need more advice.

If both the broiler ignitor and the bake ignitor are not working it is unlikely they are both bad. You may have another problem. Need to check voltage to the ignitors to be sure.

here you go

ftp://ftp.electrolux-na.com/ProdInfo_PDF/Lassomption/318205115en.pdf

the oven sensor needs replacing, 2 secrews hold itin its locared in the upperleft hand corner on oven cavity, pulls right out and new one plugs in.

F3 Oven temperature sensor open Replace oven temperature sensor

Hello jaronwayne
Welcome,

That range does have sealed burners.
Are you sure it has a pilot light and not Electronic ignition?

Where I live , if we call public service they will come out for free and light it for you!

I'm checking that model and I'll get back to you!
Huuum

Yes you can go with another regulator .

Thats good option than spending too much money.

Hello jiverson,
Welcome,

You said, your get a recurring F1 beep even after I press "cancel" I worked with the oven for about 2 hours trying various combos of opening the oven, pressing cancel and trying to perform various functions (light, clean, bake, broil, etc.) to no avail. I got it to stop for about an hour at one point, but it started right back up again. It also seems that every now and then the oven light will come on all by itself during one fo these alerts

Please send me your complete model number including the single diget at the end of the model number.
For example: FGB24S5AW1
Then I can be sure!!!!!!!!!!!
Waiting your response. I'll check for it through out the day!
And get back to you as fats as possible so you can take care of it Monday!

Huuum

In some ovens It could be failure of your, EOC (Electronic Oven Control) failure

It was an electric ignition
Thank you