20 Most Recent Frigidaire FGB24S5A Gas Single Oven - Page 4 Questions & Answers

HI. this is a oven temp sensor failure notice. you will need to check the wires leading from the temp sensor to the control. if the wires are in good condition and , the sensor harness is not welded, replace the temp sensor asap.

this could be as easy as a bad switch
or your door might not be closing enough to diengage the light
push the door in with your hand as hard as you can with out pushong through the glass
if the light goes out its your door adjustment or hinges
if it does not,,,
open the door and try the switch by hand
again if it goes out its the door
if not well then it is just your switch
ive included the link so that you can
see how and where it goes as well as order the part

i do hope this helped you out
have a great day

clean the orfices and tubes and then if possible adjust your air mixture setting also

You probably have a weak ignitor. To operate properly it should draw 3.5 amps or better. The ignitor must be bright. If it is dim it is weak.
Some repair pix
If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

bake ignitor is coming on but it will be weak. about $70 for part

the oven vent goes out the top so not to worry

DO NOT USE THE OVEN until you replace oven control
thank you...garing
l

Here's a diagram of the oven along with the Oven Ignitor (Part #19 on the diagram) and the Broiler Ignitor, (Part #26 on the diagram). They are located behind the gas deflectors located at the top and bottom inside the oven compartment, accessible from inside the oven, but you'll need to remove the rear panel at the outside back of the stove to disconnect the terminals tha supply voltage to the ignitors.

Be sure to turn the breaker off and/or unplug the range from the 220V-AC outlet first.

http://www.searspartsdirect.com/partsdirect/getSubComp.pd?modelNumber=FGF353BADB&productCategoryId=0124002&brandId=1428&modelName=FRIGIDAIRE-GAS-RANGE---5995274411&diagramPageId=00003&componentDescription=BURNER&documentId=Y2702738&backToLink=Return%20to%20Sub%20Components%20list

Hope this helps you complete your repair. Best Regards!

Your thermocouple needs replacement. Its the thin tube next to the pilot, it runs alway back to the gas control valve. When it fails the gas valve won't allow the gas to flow. Turn the gass off before begining repairs, and NO OPEN FLAMES OR SMOKING!

One of the switches is stuck,causing circuit to 'think' that you're trying to light a burner. Give each control knob a good 'tap' with the back of a screw driver.If that doesn't free it up, we will have to find the stuck
switch
If you need further help, I’m available over the phone at https://www.6ya.com/expert/craig_3fa289bf857b1a3c

Hi,

It sounds like you have a faulty solenoid on your FSD (Flame Safeguard Device) This should,when working correctly, allow a small amount of gas through to the burner, if faulty no gas will come through despite being turned on at the control.

It's quite a fiddly job and i would highly recommend a 'Gas Safe' engineer take a look at it for you.

I hope this helps.

I am not sure. However, people in our area of sc, have had burner problems because a local utility added propane to their natural gas because they got it a bargain. guy

if its an anti frost one it might think its freezin up probly something wrong with the thermostat

Inner or outer? you will have to take the door off, done by lowering door to full open postion and youll see a fold down flap at hinge, fold down and close door and lift. this will allow you to access screws easier. remove handle and four bottom screws. that will allow you to take off outer glass....there will be screws on inside to take out inner glass.

OK, I will list the Possible causes and the solutions below to combat this issue you are experiencing.


POSSIBLE CAUSES--


1. Door motor failure / jammed. Latch
motor switch failure.
2. Control software failure, or component
failure (relay stuck).
3. Wiring Problem.


SOLUTIONS--


1. Press CLEAR key.

2. If CLEAR key does not eliminate problem, turn off power for 30 seconds, then turn on power.

3. Check wiring of Lock Motor, and Lock Switch A, and Door Switch circuits.

4. Unplug P4, apply power (L1) directly to the Lock Motor, if the motor does not rotate, replace Lock Motor Assembly. Plug P4.

5. Check Lock Switch A for proper operation (do they open and close, check with ohmmeter). The Lock Motor may be powered as in above step to open and close Lock Switch. If the Lock Switch
is defective, replace Motor Lock Assembly.

6. If all above steps fail to correct situation, replace control.

HI, this control(clock/timer), will need to be replaced at this time. this code represent a control fault within the chip set(logic). this control has failed.

try pushing self clean then cancel or stop/clear

Hi, The oven should ignite within 20 to 30 seconds. The most common problem is that the ignitor gets weak and will not open the gas valve like it should. This would be my first part to change.