20 Most Recent Cuisinart Coffeemakers - Page 8 Questions & Answers

I had the same problem, first you need to use a putty knife to push the latch back so you can open it. second once it is open take out the 4 small screws holding the head unit into the lid. Once the unit drops you can then wedge the two parts back into their proper alignment and put the whole thing back together. It is a pain but doable. took me about 30 minutes.

I don't think there is one.

Google model name and number and type users/owners manuals.

Seems like this model has alot of issues based on what I am reading on the internet. First thing you should do is make sure that your plug is working by moving your Cuisinart to a plug that you know is working or plugging something in that same plug that runs, so you know the breaker or GMI switch isn't tripped. Next, contact Cuisinart for assistance. I located the manual and it says nothing about troubleshooting issues like this. Contact information is included in the manual though, so here it is: https://www.cuisinart.com/share/pdf/manuals/em-200.pdf Hope this helps.

Since you just bought it, please consider returning it for refund or warranty repair or replacement.

It may require assistance from a trusted relative or friend, or a technician. Example of method to disable the noise, which bothers pets. http://mongolianquill.net/2011/10/disable-the-obnoxious-beeping-on-a-mr-coffee-model-jwx27/ Disable the obnoxious beeping on Mr Coffee Model JWX27 Mongolian Quill

Doesn't brew a full cup. Every once in a while an air bubble may get trapped in the water path. Lift off the reservoir, then put it back into place. Turn off and unplug the brewer for 30 seconds or more. When you plug the brewer back in, be sure to turn the power back on. The exit needle may be clogged (refer to "Cleaning & Maintenance" page 18). Clean the K-Cup® holder brewing chamber (refer to "Cleaning & Maintenance" page 18). Make sure the water reservoir is properly in place, and perform a Rinse cycle. De-scale the Brewer (refer to page 20). If you have repeated the de-scale procedure two times and it is still only brewing a partial cup, contact Customer Service at 1-800-726-0190. Cuisinart SS 700 Instruction Booklet Good luck. Semper Fi, Z

First, I'm not a Cuisiart Tech, but I have worked on commercial equip and similar table top machines. Call your vendor or MFR for help. Check your manual for "Storage" or "Shipping" instructions. *** the following is for information only *** * At work we had to test all these types of units prior to installing into a customer's location. In most cases it was not a problem to leave the water in the "Internal Tank Boiler" as it won't leak under normal conditions. Removing the water may also cause problems at start up. Air bubbles in lines, etc. * Once in a while we had to send it via post office which requires liquids to be drained or protected with absorbent padding and placed completely in a water tight bag(s). * Draining (if not explained by the MFR or in the manual) is tricky and requires the unit to be disassembled (voiding warranty) to get at the inner tank plumbing. Removing the hose at the bottom of the heater tank will allow the water to be drained. Reattach all hoses and leave a note that the machine has no water and needs to be re-initialized like a new unit from the MFR or store. Not following the pre fill instructions will cause an element burn out and ruin your machine. * I've come across a youtube vid that gets you to the location of the tank (it's connected directly to the pump) but be warned that this is not for the faint of heart and will certainly void the warranty: https://www.bing.com/videos/search?q=cuisinart+ss700+drain+for+storage&&view=detail&mid=90CE1CEFE40B3CCA842690CE1CEFE40B3CCA8426&&FORM=VRDGAR Aloha, ukeboy57