Top 20 Jenn-Air JGR8850 Gas Kitchen Range Questions & Answers

see this link below perhaps you put weight on the door and bent it other wise unplugg and wait 10 minutes and try again to operate http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/513702-lock-f9-ignitor.html

If the ignitor continues to click and spark after the burner is lit you have a faulty "ignition module" and it will need to be replaced. Here is the part to order.

it seems to be very expensive shop arround there are alot of con men out there and he seems to be one a control pannel for that oven $105 and easy to fix no time at all $195 to fit 20 mins work at most 30mins

Hi,

The ignitor is not working right and is going bad....
have the repair man replace the ignitor, or DIY....
Check out this tip about your problem...

Oven not Working or Oven not Heating

Oven Problems Replacing the Igniter


heatman101

you need to change out the bake ignitor.when the ignitor is breaking down this is what happens,it takes longer and longer for it to ignite the flame and i've seen some ignitors burn a hole in the tub,change out the ignitor and you'll be all set,part number 74007498.

Hi,
Here is a tip that I wrote that will help figure out why the burner spark keepson clicking...

Gas Range RepairBurners Keep on Clicking
heatman101

This waht F9 mean
F9 Door latch Check door latch components.
You will need to replace door latch

Hi,

The ignitor is not working right and is going bad....
have the repair man replace the ignitor, or DIY....
Check out this tip about your problem...

Oven not Working or Oven not Heating

Oven Problems Replacing the Igniter


heatman101

Kathy,
The burner in the oven that has the fan going on is leaking. May be a small leak but a leak nevertheless. So please have its gas pipe removed and replaced soonest. Then the has smell and the fan running on its own will cease.

Hi,

Here is a tip that I wrote that will help figure out why the burner spark keeps on clicking...Gas Range Repair Burners Keep on Clicking

heatman101

The problem is usually the igniter not reaching the correct amp draw .When the igniter does not reach the correct amp draw it may allow the gas valve to partially open or not open at all. The igniters are inexpensive and easy to replace. This video will walk you thru the correct procedure for testing an oven igniter. It may be a different model but the testing will be the same.You can also enter your model # for diagrams and illustrations of your specific model. Not all models are available. All parts come with installation instructions.

Hi


Thanks for using FixYa. Error code F1 means that the touch pad is defective. To resolve this issue you’ll have to replace the touch pad. Please do rate the solution if the issue is resolved or post a comment for further assistance.


Thanks
Rylee

go ahead no problem

Hi,
Here is a tip that I wrote that will help figure out why the burner spark keeps on clicking...

Gas Range Repair Burners Keep on Clicking
http://www.fixya.com/support/r4033033-gas_range_repair_burners_keep_clicking

heatman101

Hi Mark,

The symptoms you are experiencing are consistent with the hot surface ignitor getting weak.

This ignitor called a glow bar will increase it's resistance with age. With this higher resistance the current that goes to the gas valve for the oven is lowered, causing to open slower (hence the gas odor) and eventually not at all.

This can be verified with an amp probe on the ignition system. It should draw 3.2 amps for the gas valve to open. If an amp meter is not available you can actually swap the broil and bake ignitors as they are identical.

Your insulation seems to be faulty and letting the heat escape.
Mark this solution as helpful if it is.

If the bake ignitor comes on (starts glowing after a few seconds) - check the amperage on the bake ignitor wires when it's on. If the ignitor is a round style - amperage should be 2.5-3A, if the ignitor is rectangular - 3 - 3.6A. If less than 2.5A or 3A respectively - replace ignitor.
Ignitor part numbers for round style ones: 4342528, WB2X9154, SGR403, 5304401265;
rectangular styles: 12400035, WB13K21, WB2X9998, SGR412, NR020, 5303935066, 814269, 9753108.
Ignitors of the same shape (i.e. rectangular) are interchangeable, if you can splice the wires.

Good luck!

Try this link to register your product:

(Respond here if it does not work and I did not get a site warning using this link)

Thanks for using FixYa.

Kelly

http://www.jennair.com/flash.cmd?/#/page/customerservice

It is recommended that you use a straight edge razor blade and push in one direction to remove anything stuck to the surface of a glass cook top. Stubborn, cooked on, substances can be cleaned by scrubbing with a light abrasive cook top cleaner and/or a green kitchen scrub pad. The green srub pads are considered non-abrasive and safe for cook tops. You can also use liquid dish detergent (such as Dawn) to break through grease and grime. DO NOT use steel wool, SOS pads, or any scouring powders. These products can permanently scratch or dull the finish on your cook top. If you have any questions please let me know. I hope you find this information helpful.

A F1 code on Jenn Air refers to a failure in the ERC (electronic range control). There is not a fix for it other than replace the control.

It looks like the part is still around if your model starts with JGR8850 that is. The price of the part is around $300.00 so.... not sure if it would be worth putting that into this, your call