20 Most Recent Jenn-Air SCE30600 Slide-In Electric Kitchen Range - Page 4 Questions & Answers

you have a touch pad issue, whats the model and serial ill look up the part for you, sometimes you can just get the key pad, sometimes comes sa a whole console or as part of the electronic control itself.

FC replace oven temp. sensor

f7 is listed as being a stuck membrane switch for longer than 30 seconds, a button is failed and is stuck in. replacemnet is on ly fix you cant repair active overlay switches

heat has weakened the springs on the door at hold it closed as tempertures change or people walk by the door light switch is activated the answer is to replace the door springs.

i would pull unit out adn look for a bad thermostat on back wall wired inline from bake and broil elemnts, probably tripped during a clean cycle or something got to hot, common for oven to shut down because of bad safety thermo, yet stovetop function without interuption

the most common remedy is to replace the LED readouts in the oven they burn out they are light emitting diodes, that sometimes dont last long.

it sounds like the clock on the oven has been adjusted, if the clock has been adjust the fan will continue to "Cool Down" the oven for the period set on the clock, it is also a possibility tht the clock is faulty, is the clock digital or Analouge

I think when they are saying ohm sensor, they are trying to say to test the resistance (ohms) of the temp sensor/thermistor.

So either the element is not shutting off (power supply to it), the temp sensors faulty (or too close) or the element if faulty(would be my first step)

Knowledge is from my own version of logic this is not my field of expertise but decided due to "any guidance request" I'd put my 2 cent in, but I'd say element if you haven't changed it or it is the temp sensing device, but then thinking about it if your last board in another area got zapped then maybe it is whatever circuit that provides power to the element

Cheers
S.

The gas line was stuck clean nozzle w/ small neddle and clean burner set the edge of the burner in order complete gas will be burn.

you have a common problem for that oven the key pad fails from wear try to find a replacement it should be fine after that.

convection ovens are designed to not operate when the door is not closed you must first repair the door so it closes correctly it is a safety design.

f-5 means the clock/oven control is bad. the only way to fix this is to replace the oven control

dont wory kishk help is at hand ,im a profecional oven cleaner ,and would in almost all cases be able to strip the oven door for cleaning .and it want cost the earth

F1 Defective touch pad or membrane Replace touch pad or membrane (this problem is usually the touch pad) F1 Watchdog on board Replace touch pad or clock assembly (also called the ERC) BUT you also need to check the Oven Temperature Sensors The Oven Temperature Sensors should read room temperature, 70°F, the resistance is 1000-1200 ohms. make sure you pull off the wires to measure the sensor's resistance and it reads open it is bad. and you will have to replace it too. hope this helps.

its alot of fun and its like a big puzzle i would call the pros. if not good luck and have fun lol

There are several possible reasons why your Jenn-air JGS9900 gas range may not have power:

1. Tripped Circuit Breaker: Check the circuit breaker for the range in your home's electrical panel to see if it has tripped. If it has, reset it.
2. Loose Electrical Connection: Check the power cord connection to the range to make sure it is secure. Also, check the wiring connections behind the range to ensure they are properly connected.
3. Blown Fuse: If your range has a fuse, check to see if it has blown. You may need to replace it.
4. Faulty Control Board: The control board is responsible for supplying power to the range's electronic components. If the control board is faulty, it may need to be replaced.
5. Faulty Igniter: If the burners are not igniting, the igniter may be faulty and need to be replaced.

If none of these solutions work, it may be best to contact a professional technician to diagnose and fix the issue.

There are a few potential issues that could cause the problems you're experiencing with your Jenn-Air broiler. Here are a few things you can try:

1. Make sure the gas supply to the broiler is turned on and that there are no blockages in the gas line.
2. Check the gas valve to make sure it is open and functioning properly.
3. Make sure the gas burners are clean and free of any debris or obstruction.
4. Check the broiler burner for proper ignition. It should ignite within a few seconds of turning on the broiler. If it does not, the burner orifice may be clogged and will need to be cleaned.
5. Check the gas pressure to the broiler. If the gas pressure is too low, it can cause the flames to be low or go out.
6. Make sure the broiler igniter is properly seated and connected.

Yes they can. Turn the gas off and call for service. You can't fix it yourself, you have to be a registered gas appliance technician to work on any gas appliance. The dangers of gas. Two blocks from my house, we felt it. https://www.insauga.com/five-years-ago-today-natural-gas-explosion-in-mississauga-killed-two-rocked-neighbourhood/ ..

To convert the appliance pressure regulator from one gasto another, do either (1), (2) or (3) below: Your unit will beequipped with one of the three appliance pressureregulator types shown below.1. Remove the cap, push down and turncounter-clockwise. Turn the cap over and reinstall(figure 10).NOTE: The gas type you are converting to must bevisible on the top of the installed appliance pressureregulator cap.2. Remove plastic dust cover from cap nut on top ofappliance pressure regulator. Remove cap nut fromappliance pressure regulator (plastic dust cover comesoff with nut). "IMPORTANT" remove plastic dust coverfrom cap nut and reinstall on opposite side of cap nut.Reinstall cap nut to appliance pressure regulator andreplace dust cover. "CAUTION" be sure marking forthe type of gas to which appliance pressure regulatorhas just been converted is visible in top of cap nutbefore replacing plastic dust cover. (See figure 11).3. Remove cap and forcibly snap out plastic plunger frombottom of cap. Turn plunger over and forcibly snapback in original location (figure 12).NOTE: Plunger MUST snap into position; the gas typeyou are converting to must be visible on lower side ofplunge

Usually a problem with the door lock. Self cleaning cycles invariably break things due to the extreme heat (650'F). I advise NEVER to use them.