20 Most Recent Labtec Microphone Microphone - Page 4 Questions & Answers

Try swapping the left and right speaker wires. If the left speaker now starts working, then your amplifier is the problem.

if your computer came with a motherboard disc the sound drivers could be on it click start control panel administrive tools computer management device manager scroll to sound,video and game controllers you might see a yellow question mark? Right click to reinstall drivers or uninstall click start control panel sounds and audio,volume,advanced,speakers make sure you have selected the (((appropriate speakers))) also audio you will find 3 drop down lists make sure you have the correct settings there also click start control panel sounds and audio devices select advanced there might be a tick in the mute box untick it click start control panel sounds and audio devices you can adjust the volume there also select speaker volume you can change your settings there you can also tick in the box place icon in taskbar if his does not fix the problem

click start control panel sounds and audio,volume,advanced,speakers select the appropriate speakers from the drop down list or navigate to the device manager scroll to system devices + to expand,system speaker right click properties then select use this device (enable) also you might check the speakers plug/outlet is usually at the back of the computer you will have to open up the computer to check the lead attached to the rear of the input plug make sure the connection is good try cleaning your computer of dust using a fine air blower from a compressor making VERY sure that there is no MOISTURE in the air line specifically around the sound card and the CPU central processing unit dust causes static to build up in a computer hope this helps

The labtec webcam 1200 does not have a built in microphone. Reference: http://www.labtec.com/index.cfm?countryid=1003&languageid=1&page=gear/listing&crid=30
Most desktops do not have a built in microphone, with exceptions of the ones that come built into the monitor. You find that most sound cards have an input jack to connect a microphone. To be sure if your computer does or does not, the make and model of your computer would be needed to check the computer specifications.

Go to the control panel and make sure your audio and speakers are turned on.

Audio output chip TEA2025B. I'd replace both. http://search.digikey.com/scripts/DkSearch/dksus.dll?site=us&lang=en&keywords=tea2025b

Hmmm.. sounds like assignments got crossed/reassigned possibly when the router was installed.

Have you looked down the list of System Hardware (control panel) to see if you have any Exclamation Marks that indicate a problem to look at?

Have you looked at the settings on the speakers in the computer? i.e. mute, equalizers, volume sliders, and even some audio software differentiates between the different connections on the back and front of your computer. Try clicking or right-clicking on the little speaker in your system tray (the icons at the end of the Start bar).. you may even have an icon in there for an audio program that you want to check out.

You can try a previous restore point, but pay special note of anything you've installed or changed since that time.

Just installing software for the router shouldn't necessitate opening up the computer, although an old tactic would be to pull the sound card out and reseat it back into the slot. Since you don't want to do that, I don't think you're missing anything unless you bumped it by accident when you were attaching the cable to the router. Since it was "immediate" I would be focused on software issues as you indicate.

You might even check out the support for the Labtec website rather than the MS route you've taken already.

Good luck!!

8^)

I need more info thanks

lets just go stepwise

1. check to see if the Audio drivers are installed in the device manager if not then you might have to install them
2. check to see if the Volume button on the task bar beside the time is not showing mute symbol and the volume is raised
3. if no then double click on the speaker symbol and in the properties check to see that none of the other tabs are on the mute or at very low volume
4. now check to see that the speaker jack is connected to the right colour coded jack on the PC and the volume is appropriately high

chech first if your speaker in connected to your computer, then check also your computer if your computer driver is intalled, How to check your computer, you just right click the My Computer in your screen, chose porperties, after that click hardware, click device manager, just look if there is big question mark color yellow, if you can see this, it means your motherboard drivers is not installed, that why your speaker in not functioning,

1 wire goes between the 2 speakers
1 wire goes from the speaker with 2 jacks in it to the computer, the back of the computer should have a green port to plug in the cable to
1 wire is the power

this is a guess without seeing your setup

If the display is working, you have audio. Check your amplifier. 1300Watt adaptor ... This unit draws a very low power and that is not needed.

1. Power Off: Turn off the device.
2. Jumper Configuration: Locate the jumper labeled "S16" on the device. Initially, it should be connected to pins 2 and 3.
3. Power On (Alarm+All LEDs Flashing): Turn the device back on. You'll see the alarm LED and all other LEDs flashing.
4. Power Off Again: Turn off the device once more.
5. Jumper Adjustment: Change the jumper configuration from pins 2 and 3 to pins 1 and 2.
6. Finished: Your Porpo YH-2000 is now set to the desired angular unit mode.

If you encounter any issues, you can press the reset switch on the back of the device to reinitialize it.

this model SA rather than SC seems to be a Middle East model. The SC version doesn't have DAB. https://www.google.com/search?q=panasonic+sa-pm250+instruction+manual ..

All questions need clear 'make model (what it is)' first 3 words. https://www.google.com/search?q=fmdott085+V398 ..

Question edited for clarity, typo and CAPS. Question moved from Cars and Trucks category. Claim on the warranty irrespective of how long you have had them. They charge $180 but they cost them $20 to buy from China. Package them up and send them tracked and ask them to replace the batteries. How long is the warranty on AfterShokz? While we hope you never need it, all new Shokz purchased from authorized retailers come with a two-year warranty that begins on your date of purchase. Jan 11, 2019

How To File A Warranty Claim For Your SHOKZ Headphones

https://www.google.com/search?q=Openfit+Shokz+battery+replacement ..

Are you using the charging cables that came with it? That is a type C. Are you securely attaching the charging cable? A loose connection would keep the battery from charging. If you had a low battery, you would see a red light. That you have no light at all suggests there is no charge left in the battery. I'm not sure the reset will work with no charge which is why you ought to check the cables first. But turn it off and then hold down the Multifunction button for 10 seconds to reset it. Then turn it back on and see what happens. If you can, test the charging cable on aother device. If you have another type C charging cable, try it, just to eliminate a bad cable. If these suggestions don't work, you may try the manufacturer's customer support.

The F2100 remote is not explicitly listed as compatible with the AerialBox T2100, I recommend using the remote that came with your AerialBox T2100 for optimal functionality. If you have any specific compatibility concerns, I suggest reaching out to Dish TV customer support for further assistance.