Top 20 Konica Minolta bizhub C450P Laser Printer Questions & Answers

Well you need to log in as administrator reset the IP address the mask and gateway. it is still on the old net work and was set as static IP address which mean it not set up for DHPC Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

try removing the default settings.

Am having little Challenge if I send job to printer Bizhub c451. D job will enter printer and it will wrote System Printing and it will not print

Behind the machine very bottom where # 3 draw is there is a small hole. Unplug the machine stick a screw driver in there to manually release draw number 3. the Code is dealing with the life section of draw number 3 Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

If you wish to get some details; check the site linked here. Pull up older posts...... http://electro-medical.blogspot.com/

If you have a quick service manual it will help you easily. However you can check its manual in the web site.

Background Explain!!!!! Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Check your setting for scan. Try this site Self Help Product Support Konica Minolta Business Solutions Inc Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

It is going to require you to have a special software on you computer which only a Konica Minolta tech can get if he can since the C 450 P is rare. the soft ware which is place on your computer acts as the screen allowing access to System 1, Marketing which should be change to reflect US. (MC) Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

As I said before, It is going to require you to have a special software on you computer which only a Konica Minolta tech can get if he can since the C 450 P is rare. the soft ware which is place on your computer acts as the screen allowing access to System 1, Marketing which should be change to reflect US. (MC) Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

As I said be fore, It is going to require you to have a special software on you computer which only a Konica Minolta tech can get if he can since the C 450 P is rare. the soft ware which is place on your computer acts as the screen allowing access to System 1, Marketing which should be change to reflect US. (MC) Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

c-3425 in this case should refer to a blocked sensor behind the tray. I would suggest removing the paper and restarting the printer before re-inserting the paper. This should solve the issue.

Main Control Failure or the software that is running is a problem. Recommended you have a tech reload the firmware if not that new board $$$$$$$$$$$$$. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

off the power switch, then press hold the stop key then on the power switch

change usb connecting wire

1st from the front Open the door and removed all Imaging unit start from the black. 2nd from the left side when your facesing the c450 Open remove the waste box. 3rd from there you will see the transfer belt on both side of it you will see screw just under the transfer belt loose it. Slide the transfer belt toward you.

When you say the rear tray what do you mean, ON the document feeder tray or raising the document feeder up placing the document on the big glass. Never heard of a rear tray????? Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

codes are usally warnings that a part is about to reach life or has already reached its life I wouldn't worry about it if the end function is disabled it wont affect anything until the part fails then replace

Removed all imaging unit then below you will see PCL in every imaging unit you must clean it with soft cloth completely. When PCL is covered with dust,toner,dev etc.. the developer from your imaging unit become to fall causing developer on edge of paper(dirty copies).

Did you try to change the IP address of MFP. Please change IP address of MFP and connect the PC you are sure not giving any problem. If its works fine then connect rest of the remaining PC's