20 Most Recent
Roland SOLJET PRO III XJ-740 - Page 3 Questions & Answers
My conlog is showing minus - 11.06 kwh
You mentioned a reading of minus 11.06 kWh. Here's what it means:
Remember that this is a prepaid meter, so the negative value suggests that you've used more energy than what was prepaid
The meter has consumed 11.06 kilowatt-hours (kWh) more energy than it has generated or received.
This negative value indicates that more energy was used than supplied during the specified period.
LED Indicator:
The meter has an LED light that flashes when electricity is consumed.
When you use electricity, the meter balance decreases, and the LED light provides a visual indication of energy flow.
Plz tell me error code 21 how to fix it for ultrasonic comfort 400 nebulizsr
As you know, this is a medical device. I suggest you consult a medical professional about it as it affects your treatment. The device is Japanese in origin. The instruction manuals I encounter are written in Japanese. That may or may not prove to be an impediment to you contacting the company yourself for guidance. I am reluctant to advise you about the equipment as my guidance would be very, very general and your health is much too important for trial and error. A low battery can generate error messages. Turning it off, unplugging it, waiting a few minutes, plugging it back in and turning it on might clear the problem. Some nebulizers have a reset button.; I can't say being unable to read the manual readily. Assuring all its parts are assembled correctly is of course worth doing. The company: Koushin Industries, Inc. (Japan):
Address: 1000-1, Hirakata, Ageo, Saitama, 362-0059, Japan.
Phone: You can reach them at the provided address.
Website: Visit their website for more information: Koushin Industries, Inc. However, I find the information there to be in Japanese. Again, I suggest you consult a medical professional.
MERA WORKCENTRE 5016 U2 ERROR CODE PROBLEM
Refer to pages 92 and 98 in the manual regarding error code. Switching it off and on may help (page 32). If such does not resolve the issue, you may have to consult your system administrator or the Xerox Welcome Center. 1 (800) 835-6100
Is it possible to reset maintenance message without replacing dev and drm on estudio2822?
Resetting the maintenance message on a Toshiba estudio2822 without replacing the developer (dev) and drum (drm) units might not be possible. These units often need replacement as part of regular maintenance to ensure optimal performance and print quality. However, you can consult the user manual or contact Toshiba support for specific instructions on maintenance message reset procedures for your device.
Need manuel
The manual for the Uniden BC147XLT is not available on the Uniden website. Please contact their customer support via their website here:
http://mycusthelp.com/UNIDEN/supportcontact.asp?sSessionID=&sEmail=A few tips I found online:
Programming your scanner
1. Press Manual 1 Manual
2. Enter a frequency
3. Press E
4. Press Manual
5. Repeat steps 2, 3 and 4 as needed
6. When you finish the programming steps press Scan
Hope this helps!
Out door temperature display keeps disappearing how do I keep it. Displayed
A two part temp , humid. monitor has base ( with LCD display, Integ Circuit, batteries) and sending unit ( with similar)
Start w best guesses -
sender 1 battery(s) low,
2 not make contact w plated spring, flat metal contacts which are "HARD TO SEE corroded slightly" from previous leaking battery, hard repair, sand off, solder, better to replace metal
3 signal path interference
Base- also 1 OR 2 OR 3 like sendr and
4 low chance, contacts to LCD display, to be cleaned w drop of soap/water/swab/alcohol
Hi.I SHARP EL -6051. Pressing
First press the reset button then when the display says "RESET OK ?" press the CAPS button then the button marked "2nd" (bottom left hand corner) then press Enter. Display will then say "BUSY". Reset is then complete.
Not finding what you are looking for?