20 Most Recent
Roland VersaCAMM SP-540V - Page 8 Questions & Answers
P-01 -520 error code for Riso CZ100
The P-01-520 error code on a Riso CZ100 indicates a problem related to the master removal detection sensor. This error often occurs when the machine is unable to detect the removal of the master (printing stencil) after a certain period. Here are some steps you can take to troubleshoot and resolve the issue:
1. **Check the Master Removal Area:**
Ensure that there are no obstructions or jams in the area where the master is removed after printing. Make sure the path is clear, and there is no paper or other debris hindering the operation.
2. **Inspect the Master Removal Sensor:**
The P-01-520 error is related to the master removal detection sensor. Inspect the sensor for any visible damage or misalignment. It's typically a small optical sensor located in the master removal area. Clean the sensor carefully with a soft, lint-free cloth.
3. **Check for Broken Parts:**
Inspect the master removal area for any broken or damaged parts, such as gears, levers, or switches. If any part is broken, it may need to be replaced.
4. **Reset the Machine:**
Try resetting the machine by turning it off, unplugging it from the power source, waiting for a few minutes, and then plugging it back in. Power the machine back on and check if the error persists.
5. **Update Firmware (if applicable):**
Check if there are any firmware updates available for your Riso CZ100. Updating the firmware may address certain issues. Refer to the user manual or contact Riso support for information on how to update the firmware.
6. **Contact Riso Support:**
If the issue persists after attempting the above steps, it's recommended to contact Riso technical support or your local authorized service provider. They can provide more detailed guidance, and if necessary, schedule a service technician to inspect and repair the machine.
Always follow the recommended procedures outlined in the user manual for your specific Riso CZ100 model when troubleshooting or performing maintenance. If you don't have the manual, you may be able to find it on the Riso website or by contacting their customer support.
Conon ir 2520 erore code e000750
Cause of the error code is a version mismatch with the bootROM file and the bootable/language file.
Re-launch the firmware flash and follow this order of flashing machine.
- Flash BOOT
- Flash SYSTEM
- Flash Language
- Cycle power and let machine boot normally.
How i fad the one decimal place the answer of this question 0.7844 correct to 1 decimal place
You haven't made the purpose of the question very clear Miriam so I am only guessing that it is an exercise in rounding or shortening decimal fractions to make them easier to work with which is often convenient when approximations do not matter.
The general rule of rounding is to take the last figure and if it is less than 5 it is erased and if it is 5 or more it is erased but 1 is added to the next or the new last figure and the process is repeated until the fraction is shortened to the required length.
If you take the decimal fraction 0.8745, after the first stage of rounding it would become 0.875 and then after the second stage of rounding it would become 0.88 and then finally rounding to one decimal place the result would be 0.9.
I hope this helps you deal with your fraction. I apologise in advance if I have misunderstood the question.
Round to nearest thousand
Step 1 - identify the thousandths column - going to the right of the decimal point, we have the tenths column, the hundredths column, and the thousandths column
Step 2 - check the number immediately to the right of this column
Step 3 - if this number is 5 or more, add 1 to the thousandths column - if this number is 4 or less, don't add 1 to the thousandths column (leave it alone)
Step 4 - erase all the numbers to the right of the thousandths column.
In this case, the number in the thousandths column is 4. The number immediately to the right of it is a 0. Since the 0 is 4 or less, we don't add 1 to the thousandths column. Now we erase all numbers to the right of the thousandths column. I get 22.524.
Good luck.
Paul
How do i fix Error100?
Assuming this is a Canon Copier based on the error code you referenced--Bad laser assembly needs to be replaced or , if you are lucky, the laser shutter is not being actuated and you just need to find out why the shutter is not being opened. Probably just a broken plastic tab. Please post the Brand name and model # of the equipment in the future to get the most complete answer possible.
Convert mg to ml
Milligram is a unit of mass (or weight), milliliter is a unit of volume. Any conversion between them depends on the density.
62.5 milligrams of water occupies 62.5 milliliters. 62.5 milligrams of gold occupies about 3.2 milliliters.
Not finding what you are looking for?