20 Most Recent
Konica Minolta Bizhub C451/c550/c650 Toner Magenta A070330 - Page 2 Questions & Answers
Service mode 92729272 password not working
Okay. That is a KM code. I need more detail to answer your question. for instance, model #, and why do you feel you need to get into service mode? If you don't know where you are going and why you are going there, there is plenty of buttons and bits that can cause further issues with your machine.
Bizhub 367 error c6756 how do I resolve this issue
C6757: CCD power-supply voltage malfunction
Description: Power is not supplied to CCD after the lapse of a given period of time after the main power switch or power key is turned ON or the machine recovers from the sleep mode
Check:
• CCD board (CCDB)
• Scanner drive board (SCDB)
• DC power supply (DCPU)
Hi, I have code 2452 Bizhub c6501
C-2451 to C-2453 error codes are lit even if the Developing Unit, developer, and Charging Unit are replaced. This is a symptom from a customer who mostly prints black. If you increase toner density, it will be good.
Hello my machine Bizhub 600 is indicating an error code C8101 when switching it on, who can i solve this
Actually C8101 is on Rank B meaning by Open / Close the front door to clear it.
But if error code still appear, Check the connector between M3-relay CN5-DFCB J15 for proper connection and correct as necessary.
Check the connector between PS12-DFCB J15 for proper connection and correct as necessary.
Check the connector of M3 for proper drive coupling,and correct as necessary.
PS12 I/O check, sensor check
M3 operation check (change M3)
DFCB F8 conduction check
Warming up error code 2 2 hours warming up my machine bizhub 600
Sir/Mam,
Have you had the developer and drum replaced recently, or does the screen say Replace PC Drum? There are certain house chores the copier does before "Ready to Copy" it is waiting for them to get done, so that equals "Please Wait". One big item is making sure the developer and toner are properly mixed inside the image unit underneath the drum or next to it depending on the series. Might want to have the developer replaced and drum/cleaning blade normally done all together, then run the F8 procedure/Developer Charge, and make sure the counters where cleared. Did you recently replace the drum and the developer if so did you clear the counters for the drum and developer, FIRST? IF not then the copier thinks the new drum and new developer are old. The copier works on the counters that is how it knows it got a new drum and developer. Get new developer and a new drum and have it installed correctly. Counters are clear before the unit is yanked out of the machine, then you remove the image unit/drum unit replace the developer/drum and cleaning blade. (DO NOT USE A VACUUM CLEANER WHEN REPLACING THE DEVELOPER static electricity can destroy the sensor located below the developer unit. Then reinstall and RUN F8/Developer Charge. Make sure the fax line and Ethernet cable is removed can't print anything until the F8 is run. Or you will start all over again with new developer and a new drum.
Error code 4604 on Bizhub C6000
Estimated abnormal parts:
• Fusing unit
• Printer control board (PRCB)
• AC drive board (ACDB)
• Fusing heater lamp /1 (L2)
• Fusing heater lamp /2 (L3)
• Fusing heater lamp /3 (L4)
• Temperature sensor /1 (TH1)
WARNING
• After replacing the defective parts, be sure to set the DIPSW 3-1 to 0. If DIPSW3-1 is set to 0 before defective parts are fixed, it may cause fire.
Solution
1. Check the connection between the rear side connector of the fusing unit and the main body side connector, and repair it if any abnormality.
2. Check the connector connection and the wiring between PRCB and the temperature sensor, and repair it if any abnormality.
3. Check the connector connection and the wiring between ACDB and the fusing heater lamp, and repair it if any abnormality. (Wiring diagram: Main body (1/3): 3-E)
4. Check the installation condition of the fusing heater lamp and ON/OFF with I/O, and repair/replace it if any abnormality. (Wiring diagram: Main body (1/3): 3-D)
5. Check the installation condition of TH1 and temperature of I/O, and adjust/replace it if any abnormality. (Wiring diagram: Main body (1/3): 3-F)
6. Replace TH1.
7. ReplaceL2, L3 and L4.
8. Replace ACDB.
9. Replace PRCB.
Minolta codes
Level Adjustment error. Has the drum and the developer unit and developer been replaced? Has the drum unit/assy. been cleaned including the sensor!!!!!!!!!
Not finding what you are looking for?