20 Most Recent
Whirlpool LGB6300 Gas Dryer - Page 10 Questions & Answers
Dryer drum turns for a second...stops and then motor hums?
I have a strong feeling the motor is seized or at least in the process of... I would recommend a new motor. If you are mechanically inclined, it's a very easy process. If you need help, I would be more than help to walk you through it.
2/24/2009 3:21:25 AM •
Whirlpool...
•
Answered
on Feb 24, 2009
DRYER HEAT TURNS OFF AFTER ABOUT 30 MINUTES
- Get on with replacing the gas valve coils shown to you in the previous link, it will take care of your problem.
- There are two house circuits/fuses in an electric dryer's circuit.
If one of them is tripped/blown, the drum may turn, but the heater will not operate. Reset the circuit breaker or replace the house fuse.
- Outlet wired incorrectly.
Have a qualified electrician verify that the supply voltage is correct.
- Gas supply valve to a gas dryer is not open.
Open the gas supply valve. See Installation Instructions for details.
- LP gas supply tank is empty or there has been a utility interruption of natural gas.
Refill or replace the LP tank. Call your natural gas utility company.
- Dryer does not have enough air supply to support the gas burner.
The dryer needs space around it for proper ventilation. Do not stack or place laundry or throw rugs against the front or back of the dryer. See Installation Instructions for details about installing a dryer in a closet or alcove.
- Incorrect cycle or temperature has been selected.
If the Air Fluff cycle or temperature is selected, the dryer will tumble without heat. Each cycle ends with a Cool Down period during which the load tumbles without heat. Check the location of the indicator on the Cycle Selector knob.
6/7/2008 8:10:42 PM •
Whirlpool...
•
Answered
on Jun 07, 2008
Whirlpool WGD4800XQ1 Dryer-- Replaced burner coils and it worked great. The next day no ignition again.
There are about seven different possiblities and the prospective solution in each case appears to be replacement of a different part! I suppose if you have the proper testing equipment for assessing each of those parts, you might be favored with a relatively inexpensive fix. I would be embarassed to suggest you replace all in sequence until the dryer works.
Thermal Fuse: The thermal fuse is a safety mechanism that prevents the dryer from overheating. If it blows, the dryer won't heat. Check if the thermal fuse is intact and replace it if necessary.
Cycling Thermostat: The cycling thermostat regulates the temperature inside the dryer drum. If it's faulty, the dryer may not heat properly. Consider checking and replacing the cycling thermostat.
Igniter: The igniter is responsible for lighting the gas burner. If it's defective, the dryer won't ignite. Inspect the igniter for any signs of damage or malfunction.
Gas Valve Coils: Although you've already replaced them, double-check the gas valve coils. Sometimes, even new parts can fail. Ensure they are securely connected and functioning correctly.
Ventilation: Poor ventilation can lead to longer drying times and affect ignition. Make sure the dryer vent is clean and not obstructed. A clogged vent can cause overheating and affect ignition.
Door Switch: The door switch ensures the dryer doesn't operate when the door is open. If it's faulty, the dryer won't start or heat. Verify that the door switch is functioning properly.
Timer and Controls: Check if the timer advances correctly during the drying cycle. Malfunctioning controls can impact ignition. Inspect the timer and control board for any issues.
Whirlpool Dryer WGD4800XQ1 - OEM Parts & Repair Help - PartSelect.com
On a cabrio whirlpool dryer what does E4 and F4 codes mean
A "F4E4" (Low or No Line Voltage) code indicates there may be a problem with your home power supply, keeping the dryer's heater from turning on. The dryer will continue to run when this diagnostic code is present. Touch any pad to clear the code from the display and return to the estimated time remaining.
Whirlpool duet model YWED9300VU0
Try kit 4392067. It's the 4 roller wheel kit with belt and pulley. I use them all the time on that model, but without the Y in the beginning. Not sure what the variation is there.
Not finding what you are looking for?