Frigidaire 5.8 cu. ft. Electric Super Capacity Dryer - GLEQ2152 - Answered Questions & Fixed issues

If the terminal is 5/16 it needs to be 5/16. The reason is that it passes the correct resistance. The smaller the contact, the more resistance and heat. You may be okay with a 5/16 connector in 250'F and that is probably the best option. However, I would image that any local wholesale electrical wholesaler would carry them. https://www.google.com/search?q=5%2F16+high+temperature+spade+terminal Nedco and CES are my go-to wholesalers https://www.google.com/search?q=electrical+wholesaler+near+me ..

Help in the link which also refers to the thermal limiter. It is a gas appliance and should be only serviced by a certified and registered gas technician. https://www.google.com/search?q=Frigidaire+Affinity+Door+Open ..

It is a gas appliance so has to be worked on by a gas certified technician. Call for service. That is the law. ..

To put your Frigidaire Dryer FEQ1442ES0 into diagnostic mode, follow these steps:

1. Hold down the Select and Cancel buttons at the same time for six seconds. After one buzzer sound, the two keys will be released.
2. Press and hold the Select and Cancel keys for six seconds right away. The display will indicate "r 2" when the buzzer sounds once.

Once you've put your dryer in diagnostic mode, you may run the diagnostic test to find any problems. You can consult your dryer's operating instructions booklet if you require any more help. I hope this is useful.

Good Afternoon Friend, this is Z. Thank you for your post! If you are receiving an error code E61 on your Frigidaire Affinity dryer, first check if it is a false error code by resetting the power to your appliance by either unplugging it or flipping off the breaker for about ten minutes. If the error code persists, it could potentially mean that your dryer is experiencing a failure with the heater relay. This is not a typical DIY job. I would recommend reaching out to an experienced appliance tech just to ensure no troubleshooting step has been missed. You can often locate a qualified service provider through the manufacturer website. Best regards.

Thumping and grinding is indication of a worn rear bearing and worn drum slides at the front. They are made of felt and are supposed to be oiled periodically. They are an easy replacement on older machines. https://www.google.com/search?q=Frigidaire+dryer+gler642as3+parts ..

The important part that is missing from this question is the model of the dryer as this part may used on multiple models. The correct Google search query is frigidaire (model) replace timer or frigidaire (model) timer wiring diagram The result will be like this and you can click on the images tab as well. https://www.google.com/search?q=%E2%80%8Bfrigidaire+(model)+timer+wiring+diagram I deleted the Answer that you got previously as it was from an AI Answer Bot https://www.fixya.com/users/rege-oluwaseun I am an advanced human being to provide comprehensive and accurate information based on authoritative non-specific answers ..

Question edited for clarity. Question moved from Cars and Trucks. No, not normally, it comes as a unit and this is standard procedure. If it is failing in three years, you have an airflow issue which is causing overheating. https://www.partselect.com/PS418120-Frigidaire-131553900-Heating-Element-Assembly.htm?SourceCode=20&SearchTerm=GLER331AS2&ModelNum=GLER331AS2&ModelID=1107102 Having said that, here are bare coils if you want to try it and the price is a lot more favorable, just make sure voltage and wattage matches.

5300622032 Frigidaire Dryer Heating Element Coil

Reliable Parts https://www.reliableparts.ca > ... > Frigidaire Dryer Parts This is a genuine OEM part that works for some models of Frigidaire, Electrolux, White Westinghouse, and Tappan models. The 5300622032 Frigidaire Dryer Heating ... $56.81 · ‎In stock

Frigidaire Dryer Heating Element

Amazon.ca https://www.amazon.ca > frigidaire-dryer-heating-ele... Wadoy Dryer Heating Element Heater coil 5300622034 Compatible with Frigidaire Gibson Kelvinator Ken-more Tappan Westinghouse · 4.24.2 out of 5 stars (37). ..

it is you's to mount upside down, whether or not it works well.

SOUNDS LIKE FAULTY THERMOSTAT / REGULATOR FOR HEATER ELEMENT, COMMON PROBLEM IN DRYERS

There are several things it could be, but before you start throwing parts at it give these folks a call at their 800# tech line. https://www.repairclinic.com/ProductDetail/641599?symptoms=1

Control board probably needs replacement you can find the part here... https://www.partselect.com/Models/FFRE4120SW/Manufacturer/4/Sections/Control-Panel/?ModelID=6901298&ModelNum=FFRE4120SW&mfgModelNum=&ManufactureID=4&Selected=E1595D82EF749006AEC1AD26B911C7D1B16785E2&Position=2&mfg=Frigidaire&Type=Dryer&Mark=2 Suggest you call their 888# to confirm with their tech's before throwiing parts at it. Best to you. Also these guys 800# but they show special order item. https://www.repairclinic.com/RepairHelp/How-To-Fix-A-Dryer/1-2-2269837-/New/Frigidaire-Dryer-Won-T-Start-FFRE4120SW

check out these sites... https://www.repairclinic.com/ProductDetail/689318?symptoms=1 https://www.appliancepartspros.com/repair-help/frigidaire-dryer-aeq8000fe0-repair/aeq8000fe0-wont-start.html A call to their tech 800#s so you don't start throwing parts at it. :) Best to you

The Frigidaire AEQ8000FE electric dryer is displaying the 50 and start/stop lights blinking randomly with periodic beeping. Pressing the control panel clears the issue, but it returns after a few minutes. Despite this issue, the dryer is working properly.

The loud, constant squeak/squeal from your Frigidaire dryer, combined with a burning smell, indicates a serious problem that needs to be addressed. While replacing the drum bearing kit was a good step, it appears that there may be other issues at play. One possible cause of the squeaking could be a worn or damaged drive belt or idler pulley. If the idler pulley spring came off, it is possible that the belt is not properly tensioned and may be slipping or rubbing against the drum, causing the squeaking noise. Additionally, a slipping belt can generate a burning smell as it heats up from the friction. Another possible cause of the burning smell could be a malfunctioning heating element, which may be overheating the dryer and causing the burning odor. It is recommended that you stop using the dryer immediately and unplug it from the power source. It is not safe to continue using a dryer that is producing a burning smell.

f the outside of your Frigidaire dryer is hot to the touch and the heating element appears to be glowing red hot when the knob is not in the off position, it is likely that there is a problem with the dryer's heating element. It could be shorted, burnt, or damaged in some other way. It is also possible that there is a problem with the dryer's thermostat, which regulates the temperature inside the dryer. If the thermostat is not functioning properly, it could cause the heating element to stay on for too long and overheat the dryer. It is recommended that you stop using the dryer immediately and unplug it from the power source. It is not safe to continue using a dryer that is overheating or has a malfunctioning heating element. It is best to have a qualified technician inspec

It sounds like you may be experiencing issues with the heating element on your Frigidaire window AC/Heater combo unit. Here are a few things you can try to troubleshoot the problem:

1. Check the thermostat: Make sure that the thermostat is set to "Heat" and that the temperature is set to a level high enough to activate the heating element.
2. Check the air filter: A dirty air filter can restrict airflow and prevent the heating element from functioning properly. Clean or replace the air filter if necessary.
3. Check the heating element: The heating element may be faulty and needs to be replaced. Consult the manufacturer's manual or contact the manufacturer's customer service for further assistance.
4. Check the blower motor: The blower motor may be malfunctioning and needs to be replaced by a professional technician.
5. Check the wiring: Check the wiring and connections, ensure that all the wiring is securely connected and that there is no damage to the wires.
6. Check the fuses: Make sure that all the fuses are working properly and that they are not blown or tripped.

Keep in mind that attempting to repair an AC/Heater unit can be dangerous if you are not familiar with the proper procedures and safety precautions. It's best to let a professional technician handle the repair. If the problem persists, it's recommended to contact the manufacturer's customer service or a professional technician for further assistance. They can inspect the unit and determine the cause of the problem and provide a solution. Regenerate response

The control panel lock is engaged. This keeps the dryer from being turned on by accident while cleaning the panel (or by a small child). There should be a line with a padlock symbol between two buttons on the control panel indicating the ones to press and hold to toggle the lock feature. On some Frigidaire dryers, the buttons to press and hold are Options and Select. You need to hold the buttons for 10+ seconds. The LOC message should disappear when you have held the buttons for long enough. However, if you do not release the buttons, the lock will toggle back on. I hope this helps. Cindy Wells

Good morning, dissapointed81. I understand that you are experiencing some concerns with your dryer. Before contacting a service provider, I would suggest that you either unplug or turn the circuit breaker off to the unit for five to ten minutes. Let the dryer reset completely and try to use it as normal again. If this does not prove to be effective, we do recommend that a professional technician diagnose the thermal limiter and control board. The E66 error code typically indicates an error within the thermal limiter and interrupted communication to the control board. Though a full repair, and replacement parts, might not be needed we do recommend having a professional test the unit for safety reasons. -Hope this helps!

POSSIBLE BAD ROLLERS, BAD DRUM GLIDES, WORN BELT, DAMAGED BELT TENSIONER? AND BAD FELTS ON THE DRUM ITSELF