20 Most Recent Frigidaire Affinity Series FASE7073LA Electric Dryer - Page 6 Questions & Answers

that has three sets of coils in it,one of them is bad this is most likely why you still have heat,i've seen it a few times,change out the heater box,go here and look at the last picture,you'll see the three sets of coils one of them is broken,just order your heater box for your model number off of your dryer.change out the heater box https://www.appliancezone.net/134792700-frigidaire-dryer-heating-element-replacement/?gclid=Cj0KCQiAvrfSBRC2ARIsAFumcm_UzfGwntvtSVc9IDruzrS145S-0pcaF2W7iBwEOgT2y1r4boAgEPAaAoi4EALw_wcB

you have a problem with the heat you can't just say it's the element or thermistor you have to unplug it,take it apart and get in there with a meter and check all the t-stats,element thermistor,if they check good you could have a bad computer board but hopefully it will be the element but if you just bought it the dryer is still under warranty for the first year so either call whoever you bought it from or the 800 number off of the machine

It actually sounds like you have another problem that is causing this one. When you remove the front to access the felt gasket check the support rollers because you might have one or both that need replacement. I would suggest replacing the felt also and yes it does require the high temp adhesive.

frigidaire dryers have alot of problems with the control board,if it starts then fuses are good or it wouldn't run,does it start right up again?if so you have a bad board,if it doesn't start right up again the motor most likely is bad,any error codes?you could have a bad or broken wire somewhere in the dryer but like i said,they have alot of board issues,next time send the model number,if you know where the board is open up the dryer,unplug it first,then when you find the board plug the dryer back in and start it,when it stalls try tapping on the board,it might start again,if not unplug the dryer and look at the board to see if there's any burn marks on it or a bad soldier joint,also it might have a burnt smell to it.

The lint MAY have caused a thermal limit fuse to blow out. If that is the case then it has to be replaced. There is also a chance that the heater element has failed and as you saw it is like a light bulb coil. You need to inspect it very closely if you don't have an ohm meter to test it for continuity. Frigidaire 131553900 Heating Element Assembly PartSelect and Frigidaire 134120900 Thermal Limiter Limit 220 PartSelect

There is none. What is the issue that you are having with it

Replace the dryer control board.

Sounds like a stuck thermostat or sensor. Be VERY careful with this because it could burn-up. For safety reasons I suggest trash it and buy a new one.

Hi,

There can be many reasons why your dryer will not start or turn...

The most common causes are the belt breaking or jumping off, or the motor going bad...

Here are a couple of tips that I wrote will help you to figure out why your dryer will not run...

Dryer Repair - The Dryer is not Turning

Dryer Repair ? The dryer will not start


heatman101

Not real clear on the "beep" sound but the hum is most likely the electric coil on the gas valve. If the unit is functioning properly and there is not smell of gas, the only way to resolve the noise is to replace the gas valve assembly.

repairs should be performed by an authorized servicer. insure that the door is properly closed unplug the unit and perform a continuity check on the door switch. if the door switch is ok reconnect the door switch and plug the unit to the power supply. if the problem still exists then you have a control issue. be sure to call your nearest service center to schedule for a repair. have your model and serial number available.

Clickston

The door switch must be flty