20 Most Recent
Whirlpool LSR6232J Top Load Washer - Page 5 Questions & Answers
How do I fix a leaky Whirlpool washer?
Quite simply you locate the leak and replace the hoses, gaskets or the part that is leaking.
A trick is to slip some paper under it and pull it out after a few minutes to see the area of the leak. Then you can pull the machine out and tip it back against the wall to check the location.
3/19/2023 9:48:23 AM •
Whirlpool...
•
Answered
on Mar 19, 2023
Whirlpool washer setting comes up with an 8 hour cycle, it used to be 47 minutes!
Hello Kim, we're sorry to hear about your Washer. We recommend disconnecting power from the breaker for at least a minute and then turning the breaker back on to do a master reset on the Washer. If you are in need of help after trying the reset, can you please email us your address, phone number, the model and serial number, the website you were contacted on, Fixya, your review ID, and date of purchase to
[email protected]?
3/4/2023 6:41:14 PM •
Whirlpool...
•
Answered
on Mar 04, 2023
Need control knob assembly for whirlpool lsq9564mqo
If you need a control knob assembly for your Whirlpool LSQ9564MQ0 washing machine, there are several options you can explore:
- Contact Whirlpool Customer Service: You can reach out to Whirlpool customer service to see if they have the part available for purchase. You can call them at 1-800-253-1301 or visit their website to chat with a representative.
- Check Online Retailers: There are several online retailers that specialize in appliance parts, such as PartSelect, RepairClinic, and AppliancePartsPros. You can search for the control knob assembly for your specific model and order it online.
- Check Local Appliance Repair Shops: You can also check with local appliance repair shops in your area to see if they have the part or can order it for you.
When replacing the control knob assembly, be sure to follow the manufacturer's instructions and turn off power to the appliance before beginning any repairs.
2/25/2023 12:36:26 PM •
Whirlpool...
•
Answered
on Feb 25, 2023
Whirlpool Cabrio Error Message?
The error code "F" followed by a number and a dot on a Whirlpool Cabrio washing machine indicates a fault has been detected in the machine's control board. Without the specific number that follows the "F," it is difficult to determine the exact issue. You can try unplugging the machine for a few minutes and then plugging it back in to see if the error code clears. If the code persists, you may need to consult the user manual or contact Whirlpool customer service for further assistance.
2/24/2023 9:13:47 AM •
Whirlpool...
•
Answered
on Feb 24, 2023
Whirlpool washer SM8525492-B spring replacement; having trouble removing upper control
To replace the spring on your Whirlpool washer SM8525492-B, you may need to remove the upper control panel. Here are some steps you can follow to do this:
1. Unplug the washer from the electrical outlet to ensure your safety.
2. Remove the end caps on each side of the control panel. These end caps are located at the top of the washer and can be removed by pulling them off.
3. Once the end caps are removed, use a screwdriver to remove the screws that hold the control panel in place. There should be two screws, one on each side of the control panel.
4. Once the screws are removed, slide the control panel forward to release it from the clips that hold it in place.
5. Tilt the control panel back and rest it against the wall. Be careful not to damage any of the wires or connections that are attached to the control panel.
6. You should now have access to the springs on the washer. Replace the spring as necessary, and then reattach the control panel by reversing the steps above.
If you are still having trouble removing the control panel, it may be helpful to consult the washer's manual or contact a professional for assistance.
2/19/2023 10:09:02 PM •
Whirlpool...
•
Answered
on Feb 19, 2023
Whirlpool calypso drier just stopped working after working fine..can't seem to turn off all the wat
You can check to see if there is a quick fix by doing the following:
- Verify the power source: Check to see if the dryer is plugged in and if the circuit breaker hasn't tripped. Reset the circuit breaker to see if the dryer comes on if it has been tripped.
- Examine the doorknob: The dryer might not start if the door switch is broken. Open and close the dryer door to check that the door switch is functioning properly. The door switch may need to be replaced if the dryer starts when the door is closed.
- Examine the thermal fuse: If the dryer gets too hot, the thermal fuse, a safety feature, can stop the machine from working. The thermal fuse will need to be replaced if it blows.
- Examine the control panel: The control board may be defective and need to be replaced if none of the aforementioned steps resolve the issue.
2/13/2023 4:08:35 PM •
Whirlpool...
•
Answered
on Feb 13, 2023
Not finding what you are looking for?