Keurig B100 Coffee Maker - Answered Questions & Fixed issues
PIt was plugged into a power strip w/a microwave.
The Keurig has had an electrical failure inside, when it failed it tripped your power strip. Once the electrical fault in the Keurig has been fixed you will again be able to run both appliances from the power strip.
12/29/2017 7:21:51 PM •
Keurig B100...
•
Answered
on Dec 29, 2017
•
483 views
Turn it on, won't do a thing, just stopped. Lights up, thats all.
Hi Carol - Sometimes, a product just reaches the end of its life. A product that sees daily (or more use) for 7 years is a pretty good run. Assuming you have cleaned and maintained it, there little more that the end user can do. These makers are more complex that the old "Mr. Coffee" or percolator that used to adorn everyone's countertop; and will often cost more to repair than it's worth. You will find it is easier and quicker to replace it with a new one and probably makes more sense than investing good money in a 7 year old coffee maker.
12/8/2015 4:06:18 AM •
Keurig B100...
•
Answered
on Dec 08, 2015
•
156 views
Does not dispense enough water
When was the last time the unit was descaled? A build up of scale will gradually restrict and then stop the water flow.
7/30/2015 4:54:12 PM •
Keurig B100...
•
Answered
on Jul 30, 2015
•
2,498 views
My keurig is not making a full and my De-scale light is on
Run 8-16 oz of vinegar through it. That will help descale the machine. As a side note, make sure to run straight water through your maker at least five or six times (until the water doesn't smell like vinegar) once it's descaled.
2/26/2015 4:23:20 PM •
Keurig B100...
•
Answered
on Feb 26, 2015
•
298 views
Keurig B100 not pumping a cup of water through
After dismantling the B100 and trouble shooting the machine I determined that the hose leading to the air pump on the right side of the B100 allowed water to back flow into the motor. The small amount of moisture eventually caused the motor to fail.
I had to find a scrap machine, which most people that have bought this piece of equipment have just thrown it in the trash, and remove the motor from the opposite side which still functioned. Since it is designed to mount to a specific side I had to appoxy the motor into place. To keep the problem from occuring again I purchased a check valve from a local pet store and put it in-line with the motor.
This solved the problem at the source and has prevented moisture from getting into the motor. Now I am a proud owner of a Frankin Pot. It's alive!
1/17/2015 3:31:30 PM •
Keurig B100...
•
Answered
on Jan 17, 2015
•
6,718 views
Keurig blue light flashes display shows prime
Lift the reservoir, then reseat it. This will clear the prime message. If it repeatedly comes back then your machine is dead. If in the year warranty, call Keurig they will ship you a replacement. A common Keurig problem.
9/28/2014 1:11:58 AM •
Keurig B100...
•
Answered
on Sep 28, 2014
•
675 views
How do i remove casing of keurig k10
Some of the case is held with compression fittings, which you really have to be careful not to break. A long and very thin flat head screwdriver and some patience can probably get you there.
9/11/2014 9:43:56 PM •
Keurig B100...
•
Answered
on Sep 11, 2014
•
984 views
Why does the water not desperse?
Try digging out the puncturing needle on the top of the cup mechanism with a safety pin. Often, the pin gets build up from sugars & starches from non-coffee cups. If that doesn't work, try running a tank of pure white vinegar through your machine. That will dissolve any build up from hard water or lime scale.
7/1/2014 3:02:04 PM •
Keurig B100...
•
Answered
on Jul 01, 2014
•
69 views
Not finding what you are looking for?