20 Most Recent Frigidaire Side by Side 26.0 Cubic Foot Total Capacity Refrigerator - Page 6 Questions & Answers

This has nothing to do with the filter. Just a coincidence. Here is what Frigidaire says: Frigidaire Refrigerator Error Code = 4 Condition = Fridge and the control board goes through cycles but does not detect a damper connection Repair or Check = Check air damper Parts Needed = Air damper

Poor defrost water drainage

Defective water solenoid control valve

Possibly from an appliance parts supplier

There is minimal clearance but the drawers can be removed. Some judicious tugging and wiggling may be required.

Check the owners manual, it may only be a high temperature alert that will go away once it cools inside.

https://www.frigidaire.com/Kitchen-Appliances/Freezers/Upright-Freezer/

High Temp Alert If the temperature inside the cabinet exceeds 21°F (-6°C), the LED light at the bottom of the cabinet will flash and the alarm will sound. The alarm can be reset by opening and then closing the door. The LED will continue to flash until the cabinet temperature is below 21°F (-6°C).

You’re damper inside of fridge not opening y need to put in service mode to check errors codes service diagram location front bottom left side almost over dripping pan

Ur compressor or startn switch is wearing out. The motor n labor can b alotta$. The relay n switch..u cud du urself. Take it off w fridge unpluged..utube can guide u. Then bringit to an appliance or supply for testn. In meantime unplug fridge for awhile n see if symptoms clearup-it will only temporary tho. Also make sure the condensor coils are not dusty..vacuum or wipe..there on back or bottom

The control arm is a plastic paddle like piece. The usual point of failure is this: https://www.appliancepartspros.com/frigidaire-module-242270102-ap5788338.html

The SH (not 5 H) error indicates that the freezer sensor is shorted in the display. The control can't determine what the freezer temperature currently is. You need to check the wiring between the thermistor (temperature sensor/resistor) and the control board. Replace the thermistor if the wiring has no damage. If the wiring is faulty, replace that. If the fault returns, you may have a problem with the control board. Please add a comment with the model number of the side-by-side refrigerator if you need a parts diagram. I hope this helps. Cindy Wells

Check the water filter, replace as needed. Remove ice bin, empty it and let it thaw out. Put it back in place and check for ice the next morning.

https://www.rohrreinigung-24notdienst.de/rohrreinigung-d%c3%bcsseldorf/

When you replaced the thermistor, did you check the resistance of the wiring and temperature sensor back at the control board? If the wires are damaged or the connector at the control board has corrosion, the control board won't get the correct signal information. If those are fine, then the control board is probably faulty. Sears Parts Direct has the control board here: https://www.searspartsdirect.com/product/3jlv6aqwdo-0046-253/id-5304512769 . Other repair shops will have this part as well. I wish that only the refrigerator temperature sensor was faulty. I hope this helps. Cindy Wells

https://www.youtube.com/watch?v=9k81fgjOk-U

you may need a check Freon level to see if its low , usually if u have low Freon level you can touch the condenser fan rails and they should be cold because when it has Freon and it liquefies into gas it creates heat hence the coils will then get warm and hot, if they are hot or warm it may not be a low Freon level issue? I would also check the freezer thermistors , see pics there may be more than 1 thermistor in freezer section , u can also check the compressor ur self to verify as not all appliance techs are reputable or knowlagable

you would need to get a whole new board to match the output pins.

Be aware the fridge works with deadly voltages. If you have not enough technical knowledge, please don't do this yourself. With a multi meter you can measure if the voltage you apply is entering the fridge. There is not much in a fridge. You find a on / of switch, a thermostat en mostly an override switch too short a thermostat. So if you measure a voltage coming is, follow the wiring and check what the thermostat does. if it won't switch you have the cause. If it does switch, follow the wiring, and if the aggregate gets a voltage and does not run, you have a defective aggregate. I can't think of more. Good Luck.

fan being obstructed behind back panel of freezer.fan motor failure or build-up of ice from door not shutting properly

The FRS26ZSH is a #for filter need MODEL #