Kenmore Elite 22.4 cu. ft. Bottom Freezer Refrigerator with Adjusta Cube Ice Maker - Answered Questions & Fixed issues

Question edited for clarity, full make model (what is is)'. Question moved to category. Help here plus 795 Service manual https://www.google.com/search?q=795.71033.010+remove+multi+air+flow+panel ..

Question edited for clarity. Check out the video and fixes. https://www.google.com/search?q=Kenmore+Elite+model+596.+My+water+dispenser+is+leaking ..

Your defrost drain tube is clogged somewhere along the way.

Question edited. This appears to be a refrigerator. 'Make Model (what it is)' in all questions please. Question moved from 'Office Equipment and Supplies'. 'electrical print'? You mean like a wiring diagram? Normally only available to Service engineers, but some help in the link. Click on the images tab. You can narrow results by putting the "model_number" in "quotes".

Kenmore Elite 79571053010 bottom-mount refrigerator

..

It is possible the water control valve for that dispenser has failed and will not open. This happens a lot for those and the ice maker valves. All you need is the model number for your refrigerator and that will look like this for Kenmore. 213.564897 for example. and I will help you find the correct part number. Sea Breeze

I just spent the better part of an hour on this. There is a white flange with two phillips screws. If you take this off it is easier to see the mechanism, but you may be able to get it back on without removing the flange. I removed the flange. The mechanism attached to the door has a hook facing up and a smaller hook facing down. There is a hinged metal bar below this. The bar has a hinged piece with a loop on it. Pull the loop up. Now push down on the piece with the hooks ( it has a spring) and hook the smaller hook on the loop. Do this for both sides. Now the door should slide easily into the slots. Once in the slots, push down on the hook piece and release the loop. Push the loop back in place along the bar. Hopefully this does the trick for you, it did for me.

you have to send model number,on some bottom mounts there is a metal striker on the door that hits the switches,sometime that gets bent back,all you have to do is readjust the striker by bending it if screws aren't loose but i don't know what kind of bottom mount you have

https://watchonlineclub.com/

On one model you do the following: To get it out of the demo mode, press and hold the "up" and "set" pad for 10 seconds.

Been three days and you have not received reply, would go to sears customer support and they are supposed to have live support, maybe they can help.

Remove all the food from the unit and clean it with a diluted chlorine bleach solution and let dry and then do it one more time. Also get a box of baking soda and put it in the fridge to absorb odiferous smells odors

Could have a bad condensor at the motor.

FF usually means the freezer fan is not working. If the fridge is cooling poorly, check to see if the fan inside is running while the compressor is running. If not, and if there's no ice jamming it, then you need a new evaporator fan. If the fridge is cooling normally and the only symptom is the error code, then it could be a problem in the electronic control.

I have the same model and had the same problem after 3 years of use. I checked this and other sites and here's how I fixed it -- easy, peasy. 1. Turn off the power to the refrig. I have a ckt breaker for the refrig so I didn't have to pull it out of its alcove. 2. Open the bottom freezer section, pull up on the front of the middle drawer and pull it out. If you look to the back inside wall of the freezer you'll see 3 vents. 3. Make a platform that will support a common hair dryer to bring it up to the level of the central vent. I used a couple of packs of napkins topped with a towel. 4. Turn on the hair dryer. I left it on for about an hour and heard two chunks of ice fall free at about the 15 and 30 minute points. 5. Remove the hair dryer and platform, put the middle drawer back in the opposite of how you removed it, and close the freezer section. 6. Turn the power back on. 7. Put a towel on the floor to catch the water from the melting ice chunks. It's been 24 hours and the error has not reappeared. If this doesn't work, then other comments suggest that it may be the related circuit panel and you'll need to call in for repairs. I hope that this helps.

The ice could be caused by a partial thaw such as a power failure. To open bin unplug unit. Get lots of towels and a wet Vac if you have one. The use of these will become obvious shortly. Open the door and put a fan blowing on it, the same type of fan we use when it is hot to cool down. Then wait in time it will start thawing. This would also be a good time to clean it inside, you probably were putting that off. When totally thawed and dry start it up and keep an eye on it for a few days it will probably be ok. If not you have a clean unit to try some of the other suggestions.

That is difficult to answer because I do not have all the info. Start by cleaning the condenser. If it was clean be sure you have water to the icemaker if so check the freezer temperature. If they are above about ten it is to warm. Check settings. Be sure if the freezer has a fan it is ok. If the coils are full of ice check the defrost system. This should get you started.

just bang on it until it make a pop sound

An air leak around the fill tube

On hour minimum.

Jon maybe fan motor fault code.