Top 20
GE 28112EE2 Cordless Phone Questions & Answers
Why is there no base power?
If nothing works, just check the cables, connections and fuses.
is the power supply plugged in? did you try an other power supply? can you see any bad pice on the cable(s). Does the mains plug deliver any power? just some extra questions.
Both phones work except they both will not ring
I think you may have accidentally pressed the do not disturb button.It is on the base of your phone and shows red when on Just press it again.
I hope I have been of help but please do not hesitate to ask if you have any further questions.
I appreciate your vote if you appreciate my reply.
I can't seem to find
Hi,
To change the number of rings before the answering machine answers the call, please refer to the detailed steps in the attached image:
To enter the
Handset setup menu, please use these steps:
Hope this solves your problem. Thanks for using
FixYa.
How do i access the menu
Press the mute/program button to go to the main menu.
You can download the manual at
http://www.home-electronics.net/ge/pc/IB/28112EE2_IB.pdf
;;;there is a blue flashing
the phone should be reset by removing all power to the phone and base for about 15 minutes. to reset the phone remove the batteries from the phone, unplug the charger from the base AND unplug the phone line (there is voltage on the phone line) after you have reset the devices hook it all back and place the handset in the base for a few seconds to sync it to the system. do this with each handset.
be aware tho resetting it this way will remove any stored numbers from the memory.
The phone shows that the
Hello,
what you are to do to solve this problem is to fellow or apply the below, instruction below
The
Cox Voice mail Service is a service provided by the Cox Corp. that
allows you to store and check voice mail messages on your home land line
phone. Of course, because the size of the voice mail in box is not
unlimited, you will eventually need to delete some of your stored
messages to make way for new ones. Fortunately, this process is not
overly difficult, and you can accomplish it with a simple phone call.
Difficulty: Moderately Easy
Instructions
-
Dial your home phone number from your home land-line. This will bring you to the main menu of the Cox voice mail system.
-
Press the "*" key on your phone, and input your password when prompted by the computerized voice.
-
Press "1" to begin a playback of all your stored messages.
-
Press
"7" to delete each message in turn. Continue to press "7" at each
message until all the messages in your voice mail in box are deleted.
Hope this this hep?
Thank you and thanks for using fixya.
How do I increase the rings before message
Setting the Number of Rings (Excerpt from the Uniden Dect 1580 Phone manual
The ring time setting allows you to set the number of rings the caller hears before your answering system plays the outgoing message. You can set the ring time to answer after two, four, or six rings. If you enable the Toll Saver (TS) setting, the answering system picks up after two rings if you have new messages, and after four rings if there are
none. This way, if you make a long distance call to check your messages, you can hang up after the third ring to avoid long distance billing charges.
- Press Menu/Select.
- Select the Ans. Setup menu, and then the Ring Time submenu.
- Move the cursor to select a ring time (Toll Saver, 2 Times, 4 Times, or 6 Times).
- Press Menu/Select. You will hear a confirmation tone.
thanks
I have a Ge cordless phone model #
What worked for me was disconnecting both wire from base and ensuring languages are the same on base and phones. Hopefully this will help you also.
28112 series dect 6.0 cordless
I have seen this problem on other equipment with LCD screens. The connection between the LDC screen and the circuit board is an elastomeric connector. To see if this might be the problem, squeeze the phone along each edge of the LCD screen (front to back) and see if you can get the display to come back or get any better. If so, the contacting area on the circuit board needs cleaning.
Not finding what you are looking for?