Uniden DECT 6.0 Cordless Telephone Expansion Handset - Answered Questions & Fixed issues
Phone rings once, but then stops ringing and I can't answer the call
If you have a landline, most likely you have a short in it. Not enough to kill line, but, when the 90 volts a.c. comes in to ring it jumps short. The short answers the phone.. It doesn't stop out going but can cause static. Check the line at the box outside. if bad there call your phone company, if good there, trouble is in house
Out of range, buttons don't respond, battery won't hold charge
when you have a problem with anything under warranty, you take it back for new units or a refund and anything under 12 months old is under warranty
if you have lost the receipts get a copy of your bank statements as that shows where it was bought , how much it cost and when
That is a legal document to trigger a warranty action or refund
Turning the ringer on my phone. uniden 6.0
Without the model number of your Uniden phone, I don't know which silencing feature you are dealing with.
Some Uniden handsets have a Silent Mode. To toggle this on and off, press and hold the # key (below 9) for 5+ seconds when the phone isn't in use. When the silent mode is enabled, the handset will ask for a length of time for the 'no-ring' option. If no key is pressed, then the Silent Mode will continue until the # key is held again.
Other Uniden phones have Do Not Disturb. The button to enable/disable this will be on the cordless phone base. The answering system will automatically turn on and none of the handsets will ring when this feature is enabled.
You can also set the ringer volume to zero. Depending on the phone, you can reset this by pressing the volume up/down buttons or going through the menu. Look for the Ringer Volume in the same section of the menu as the Ring Tone options.
If you need additional information, please add a comment with the model of your phone. I hope this helps.
Cindy Wells
The red ID button keeps blinking even when I have no messages. How do I stop it
You might try to reset the Voice Mail Waiting Indicator ( V M W I ).
To reset the Voice Mail Warning Indicator
on the D1680 and similar handsets:
1. press [menu]
2. scroll down to "Global Setup", press [select]
3. scroll down to "VMWI Reset", press [select]
4. scroll down from "No" to "Yes", press [select]
5. handset will chirp, blinking lamp goes out,
6. press [END]
Other models, check your manual. The model number
is on a small sticker under the battery in the handset --
enter this number at
www.manualslib.com to get a free
copy of the User's Manual.
Good luck!
---------------
How do I turn off the silent mode so the phone will ring?
For the Uniden model D1680 & similar...
You ENTER "Silent Mode" by pressing and
holding the [ # ] key on the handset for a few
seconds until the display reads "Please Wait".
It will (chirp) and display "Silent Mode ON".
You can EXIT "Silent Mode" by pressing and
holding the [ # ] key on the handset for a few
seconds until the display reads "Please Wait".
It will (chirp) and display "Handset #".
Another easy way to end "Silent Mode" is to go
to the BASE and press the [ANS ON/OFF]
button to turn off the answering machine system.
(Push the [ans] button, do not unplug the power)
"Silent Mode" will clear a moment later while the
control voice tells you "Answering System is OFF"
Now you can again turn on the answering machine
system as desired.
Good luck!
------------
How do I turn off the silent mode on a Uniden 6.0 dect phone, so it will ring?
For the Uniden model D1680 & similar...
You ENTER "Silent Mode" by pressing and
holding the [ # ] key on the handset for a few
seconds until the display reads "Please Wait".
It will (chirp) and display "Silent Mode ON".
You can EXIT "Silent Mode" by pressing and
holding the [ # ] key on the handset for a few
seconds until the display reads "Please Wait".
It will (chirp) and display "Handset #".
Another easy way to end "Silent Mode" is to go
to the BASE and press the [ANS ON/OFF]
button to turn off the answering machine system.
(Push the [ans] button, do not unplug the power)
"Silent Mode" will clear a moment later while the
control voice tells you "Answering System is OFF"
Now you can again turn on the answering machine
system as desired.
Good luck!
------------
HOW DO YOU ELIMINATE BLINKING ON HANDHELD UNIT
That might be the Voice Mail Waiting Indicator.
On the D1680 and similar handsets, it is reset by:
1. press [menu]
2. scroll down to "Global Setup", press [select]
3. scroll down to "VMWI Reset", press [select]
4. scroll down from "No" to "Yes", press [select]
5. handset will chirp, blinking lamp goes out,
6. press [END]
Other models, check your manual. The model number
is on a small sticker under the battery in the handset --
enter this number at
www.manualslib.com to get a free
copy of the User's Manual.
Good luck!
---------------
Got another phone and need to program it so it will work how do I do this
First be sure the handset battery is well charged as a weak
battery will interfere with the registration process.
Then try the following ( 'works for the D1680, D1481, and similar):
( I ) Deregister the handset:
Press and hold the [END] and [ # ] keys at the same time,
after a few seconds the display will say
"System Reset, Deregister Handset"
press [SELECT]
scroll to "Base Unavailable"
press [SELECT] (chirps) press [END]
display reads "Place in base..."
( II ) Now, to re-register the handset:
Set the handset into the base cradle and wait,
after ~30 seconds the handset should display
"Handset #" and be good to go...
...or it will display "Registration Failed"
If "...Failed", try from ( I ) again.
Good luck!
--------------
How do I turn off silent mode
"Silent Mode" is entered by pressing and holding the [ # ] key
on the handset for a few seconds (model D1680 & similar).
The easy way to end "Silent Mode" is to go to the BASE and
press the [ANS ON/OFF] button to turn off the answering
machine system. (push the button, do not unplug the power)
"Silent Mode" will clear a moment later and you can again
turn on the answering machine system as desired.
Good luck!
------------
Phone is stuck on silent mode
"Silent Mode" is entered by pressing and holding the [ # ] key
on the handset for a few seconds.
The easy way to end "Silent Mode" is to go to the BASE and
press the [ANS ON/OFF] button to turn off the answering
machine system. (push the button, do not unplug the power)
"Silent Mode" will clear a moment later and you can again
turn on the answering machine system as desired.
Good luck!
------------
Reset answering
To reset the Security Code for remote access into the
answering machine system ( model D1680 & similar )
1 press [menu]
2. scroll to "Ans. Setup" press [select]
3. scroll to "Ans. Setup / Security Code" press [select]
4. first digit will be blinking, enter two digits of your choice
5. press [select]
6. press [END] to conclude & exit
Good luck!
-------------
Not finding what you are looking for?