20 Most Recent Lexmark X2500 All-In-One Printer - Page 4 Questions & Answers

hey dude have you find any solution for your problem?? i've got the same problem here :( can't do anything

You may refer to this article http://bit.ly/RGx7VV .

Check that the cartridge is properly i9nstalled. Unplug unit for about 5 minutes. Plug back in, it should re-boot and work. murf427

Check your printer "Control Panel" for blinking lights, go to page 70 in manual to see what they mean...also

http://www.lexmark.com/publications/pdfs/2007/2500/v3709407_en.pdf#xml=http://support.lexmark.com/lexmark/index?page=answeropen&segment=SUPPORT&userlocale=en_US&locale=en&type=open&searchid=1299205164822&answerid=16777216&iqaction=6&url=http%3A%2F%2Fwww.lexmark.com%2Fpublications%2Fpdfs%2F2007%2F2500%2Fv3709407_en.pdf&productCode=LEXMARK_X2500&highlightinfo=106955281,38648,38676,39676,39719,41015,41144

Also go into your computer "control panel"

1. Printer and Faxes
2. Right Click your printer -- Select Open
3. Printer Panel -- Select printer --- cancel all documents
   

The X2500 takes these toner cartridges.

According to the specs, this printer connects to the computer using an USB cable.The only reason it could be asking for an IP address if it is connected to a network card or attached to a print server.OR the wrong print driver is installed.You can download the Lexmark printer drivers from theirsupport WEB site. Please click on this link and select your model printer todownload :-http://support.lexmark.com/index?page=home&locale=EN&userlocale=EN_US&segment=DOWNLOAD

http://support.lexmark.com/index?page=home&locale=en&userlocale=EN_USlexmark drivers homepage

This article from the Lexmark website might give you an idea on how to re-seat the encoder strip back to its position: Printer Cartridge Stalls or Is Blocked

This article from the Lexmark website might give you an idea on how to re-seat the encoder strip back to its position: Printer Cartridge Stalls or Is Blocked

If you are encountering power problems with your printer, please go through the following checklist:

• Make sure the power cord is plugged in securely and directly to the power outlet. Power surge protectors can draw power away from the printer.
• Disconnect the power cord from the power outlet and the back of the printer and then reconnect it.
• Check the power supply box (if there is one) to see if it is warm or cold, as there could be a defective power supply issue.
• If there is access to a voltmeter, test the power supply to ensure that it registering the correct amount of voltage (most Lexmark printers have a 30Volt output).
• Make sure the correct power supply is connected to the printer.

It could be just a slight communication failure between your cartridges and the printer. Try to re-seat the cartridges by removing and re-inserting them into the cartridge carrier.I hope this helps.

Leading cause of paper jams is debris / foreign objects that accidentally fell into the paper feed area. Please try this approach to fix the problem:

1. Remove the sheets of paper from the feeder.
2. Grab a flashlight and look inside the feeder for any debris or foreign objects.
3. If you're willing and physically able, you may also carefully turn the printer over. Any debris should just freely roll out from the feeder.
4. If feeder is clear, place the printer on the table. Open the printer cover and remove the cartridges.
5. Check the cartridge area for any obstructions in the paper path.
6. Close the printer cover.
7. Re-brick your printer by pulling out the power supply - the black box where the power cord is plugged into. Re-plug after 30 seconds.
8. When the printer turns on, reinsert the cartridges and load some paper. Try to print again to verify that the problem is fixed.

It works, just used my #14 lexmark after refill. I put tape on the 4 bottom points of each sides. You will see 1 alone at the bottom and 3 in a group in the middle, tape the 4 and do the same on the other side. Put it back in the printer and it works... It will dispay a '?' on the ink cartridge level and status when you print.

try DAEMON TOOL LITE it works...!!!

A quick fix for most communication errors can be achieved by resetting the printer and/or rebooting the PC. Simply disconnect the printer from your computer (if USB connected)> reboot your pc > unplug and re-plug the printer into the power source to reset it. When the printer turns on, reconnect it to your computer (if USB connected). Then try to print again once the computer fully recognizes the USB connection or when the WiFi light on the printer turns solid green (if WiFi connected.).

If that doesn't help, try the steps below:

1. Disconnect the USB cable connecting the printer from your computer.
2. On your computer, go to Control Panel > Printers and Faxes.
3. Delete the Lexmark print object.
4. Reboot computer.
5. Re-brick your printer by pulling out the power supply - black box where the power cord is plugged into on the back of the printer, and re-plug after 30 seconds.
6. When the printer turns on, reconnect it to the computer.
7. Wait until your computer fully recognizes the USB connection. To check, go to Control Panel > Printers and Faxes. If you see a new Lexmark print object in the list, try to print a document to verify that the problem is fixed.

You may also try to update your printer driver by visiting the Lexmark website at http://bit.ly/tzBulE. Select your operating system, download and execute the file.

Sounds like a scanner hardware problem. It would be best to contact Lexmark Technical Support Center for assistance.