There could be several reasons why your subwoofer has stopped working on your Norcent 1950 audio system. Here are a few potential causes:
Power issue: Check if the subwoofer is receiving power. Ensure that it is properly plugged into a working power outlet and that any power switches or buttons on the subwoofer are turned on.
Connectivity issue: Verify that the subwoofer is properly connected to the audio system. Ensure that the cables are securely plugged into the correct audio outputs on the Norcent 1950 receiver or amplifier.
Settings and controls: Check the audio settings on your Norcent 1950 system to ensure that the subwoofer output is enabled and properly adjusted. It's possible that the subwoofer level may have been inadvertently lowered or muted.
Defective subwoofer: If none of the above solutions resolve the issue, it's possible that the subwoofer itself may be defective. In this case, you may need to contact Norcent customer support or bring the subwoofer to a professional technician for further diagnosis and repair.
It seems like there might be an issue with the disc recognition or loading mechanism of your Pioneer PD-F805 CD player. Here are a few steps you can try to troubleshoot and potentially resolve the problem:
1. Power cycle: Turn off the CD player, unplug it from the power source, wait for a few minutes, and then plug it back in. This simple reset may help resolve any temporary issues.
2. Check the CDs: Ensure that the CDs you are using are in good condition, free from scratches, and not warped. Sometimes, damaged or irregularly shaped CDs can cause reading errors or problems with the loading mechanism.
3. Clean the player: Use a CD lens cleaner to clean the laser lens of the CD player. Dust or debris on the lens can interfere with the proper reading of CDs and cause incorrect disc recognition.
4. Reset the player: Some CD players have a reset button or a reset procedure mentioned in the user manual. Check the manual for your Pioneer PD-F805 to see if there is a specific reset process you can follow.
5. Check the loading mechanism: Open the CD player and visually inspect the loading mechanism for any loose parts, debris, or obstructions that may be causing the incorrect disc recognition. Gently clean the mechanism if necessary.
6. Lubrication: If you're comfortable with electronics and have experience with repairing devices, you can try lubricating the moving parts of the loading mechanism with a suitable lubricant. Be cautious and use only a small amount of lubricant designed for electronics.
7. Seek professional repair: If the above steps do not resolve the issue, it might be best to consult a professional technician or contact Pioneer's customer support for further assistance. They will have the expertise and specific knowledge to diagnose and repair the problem accurately.
Remember to exercise caution when opening or attempting to repair any electronic device, and if you're not confident in your skills, it's always best to seek professional help to avoid causing further damage.
This might help
To troubleshoot a Q-See NVR 8816 recorder, you can follow these general steps:
1. Power cycle the NVR: Turn off the NVR, unplug it from the power source, wait for a few minutes, and then plug it back in. This can help resolve temporary issues.
2. Check network connections: Ensure that all network cables are properly connected to the NVR and your network infrastructure. Make sure the network connection is stable and the cables are not damaged.
3. Check camera connections: Verify that the cameras are properly connected to the NVR. Ensure that the camera cables are securely plugged into the appropriate ports on the NVR and the cameras themselves.
4. Check power supply: Ensure that the NVR and cameras are receiving power. Check that all power cables and adapters are securely connected and functioning correctly.
5. Monitor display: Verify that the NVR is connected to a compatible display device (such as a monitor or TV) using the appropriate video output method (HDMI, VGA, etc.). Ensure that the display device is powered on and set to the correct input source.
6. Network configuration: Ensure that the NVR is correctly configured to connect to your network. Verify that the IP settings, including the IP address, subnet mask, gateway, and DNS settings, are properly configured.
7. Check hard drive status: If you are experiencing issues with recording or playback, verify the status of the hard drive installed in the NVR. Check if the hard drive is recognized and functioning properly. You may need to replace or reformat the hard drive if it is faulty.
8. Firmware updates: Check the Q-See website for any available firmware updates for your NVR model. Updating the firmware can resolve known issues and improve system performance.
9. Reset the NVR: If you are still experiencing problems, you can try performing a factory reset on the NVR. Refer to the user manual or contact Q-See customer support for specific instructions on how to reset your NVR model.
If the above troubleshooting steps do not resolve the issue with your Q-See NVR 8816 recorder, it is recommended to contact Q-See customer support or consult their online support resources for further assistance. They will have the expertise and specific knowledge about your device to provide you with accurate guidance and solutions.
Check the power source: Ensure that the power source supplying electricity to the timeclock system is functioning properly. Make sure the power outlet is receiving power and the circuit breaker or fuse for that outlet hasn't tripped or blown.
Verify power connections: Check the power cables and connections for any damage or loose connections. If necessary, unplug and reconnect the power cables securely.
Restart the system: Sometimes, the timeclock system may encounter temporary glitches. Try restarting the system by unplugging it from the power source, waiting for a few seconds, and then plugging it back in.
Check battery backup (if applicable): If your ATS Timecom timeclock system has a battery backup feature, ensure that the battery is properly connected and charged. If the power outage was brief, the system might still have battery power to continue functioning. If the battery is low or depleted, consider replacing it.
Contact technical support: If you have followed the steps above and the timeclock system still does not power on, it is recommended to contact the technical support or customer service of ATS Timecom. They will be able to provide you with specific troubleshooting steps based on your system model and configuration.
On? The Smiggle button on top when pressed offer the current time as has been set. Here is a YouTube describing setting the time: https://www.youtube.com/watch?v=dEtpntejh7E
I cant believe I found this just now: http://clashofclanshelper.com/ - you receive free Clash of Clans gems instantly! Everybody uses this now! (IzozRftDa4)
A program from Diversoft called Driver Genius when used will search your computer for lost, old, or non-existent drivers.
It will download the drivers for the sound system on the board and install it for you.
ManualsLibhttps://www.manualslib.com > ... > AVS58
View and Download Cocoon AVS58 user manual online. ... 6.6.1 This is an example of a typical setup connecting the AVS58 Receiver to the receiving TV via RCA ...
What does the instruction manual say about what to use?Personally I buy Taiyo Yuden and have never had a problem. In Radio we used a lot of CDRW900 units and they used them many times a day using standard data discs. Name brand discs like Maxell and the rest are there for profit- they don't make discs so they do not regulate the quality. Go to supemediastore.com and read up on media quality and you will end up with what I use.
