20 Most Recent Cisco ASA 5505 Firewall - Page 7 Questions & Answers

call cisco

No, both of them are power supplies. PWR-2911-AC is the standard power supply but the PWR-2911-POE is a bigger power supply to power up EHWIC or single/double-width line cards. Moreover, there is no physical way to put two same/different power supplies into a 2900 router. But 3800/3900 routers can support dual power supplies. Cisco 2900 Router Price Buy Cisco ISR 2900 Series Routers 3Anetwork com

1) FR should be supported in IPBase license >>Offers features found in IPBase IOS image on ISR 1800,2800 and 3800 + Flexible Netflow + IPV6 parity for IPV4 features present in IPBase. note X.25 is mentioned in the first table FR it isn't. 2) You need to purchase a PAK and you should be able to generate the DATA license SAL from the portal following the instructions (there are also other methods described in the document) 3) you need SEC for IPSec VPN it means another PAK to buy 4) yes you can install all of the additional licenses in a single device 5) yes, they build on IP Base so you add features without removing any 6) no, the new device will be already with the correct licences from factory >> On each shipped device IPBase software activation key is installed by default. Additional keys are installed by manufacturing depending on the customer order. 7) yes with the UC PAK Hope to help

This problem is hard to answer, i think u can refer to the material about Cisco STP, if u still don't know it clearly, u can send email to our CCIE expert [email protected] to solve ur problem. : )

You can choose the transceiver SFP-10G-ER or GLC-EX-SMD, these two all can transmit up to 40KM. and more than 75% OFF at 3Anetwork.com for Cisco optic transceiver.

The main difference between WS-C2960X-24TS-L and WS-C2960X-24TS-LL as below: WS-C2960X-24TS-L 4 SFP Uplink, WS-C2960X-24TS-LL 2 SFP Uplink. WS-C2960X-24TS-L supports FlexStack-Plus stacking while WS-C2960X-24TS-L does not. WS-C2960X-24TS-L with LAN Base feature set, WS-C2960X-24TS-LL with Lan Lite feature set. I hope it can help you. WS C2960X 24TS

You probably need a new box. Contact your cable company. I might not mention the part about your son and the water....

Depends on the device. Have to go to a Cisco forum for the quickest help or directly to Cisco. Just call them. Act like it is urgent! :)

If you can't hardware reset by pressing the reset at the bottom of router for at least 5 seconds then you need to do a software reset.click on following link to go through the right procedure..... http://kb.linksys.com/Linksys/ukp.aspx?pid=10&vw=1&articleid=3676 please vote thanks.

I am assuming you are referring to the console ports on your cisco Router. You need a terminak emulation program and a serial port on your p.c. Once you connect to it set up the Vlan interface so you can use the fast ethernet interface to connect. https://www.hilgraeve.com/hyperterminal/ http://en.wikipedia.org/wiki/List_of_terminal_emulators

being cisco it could be anything as system administrator can set it to anything they like.

Cisco Quest is a cloud access system, if you disable it you may loose your access to your desktop storage, apps etc. Have a look in your start-up applications to see you can disable it temporarily, to see what effect it can have. Type in "msconfig" in the run box to access the start up applications list.

Yes, u even don't know, and Cisco deliver the End of Sale and End of Life Announcement for the Cisco Catalyst 3560V2 and 3750V2 Switches announcement for a long time, for the detailed models, maybe u can get the answer.

'192.168.0.116' is the wrong range for the router. The Cisco manager allocates the ranges the router will use. See this page on the setup. Getting Started Guide Cisco 3700 Series Access Points

Yes. Free ongoing Cisco IOS Software updates for certain fixed-configuration and stackable Cisco Catalyst switches at no additional cost is offered. For the life of the product, updates within the Cisco IOS Software package purchased (LAN Lite and LAN Base) will be made available. Cisco Switch Price Buy Cisco Catalyst Switches 3Anetwork com

Catalyst 3850 Series Switches support full IEEE 802.3at Power over Ethernet Plus (PoE+). The switch classifies the detected IEEE device within a power consumption class. Based on the available power in the power budget, the switch determines if a port can be powered (class 0,1,2,3,4). You should be aware of maximum POE power you exact model can proide - check the datasheet!

To reset the Linksys back to the default settings - Press and hold the pinhole RESET button at the back of therouter with the power ON for 20 secs. then release the RESET button.
To connect to your wireless router, the router's wireless settings needs to beconfigured with the SSID, encryption etc. and also the wireless cards in allthe laptops/computers needs to be configured with these router's wirelesssettings. Then the laptops/desktop computers can communicate with your wirelessrouter.
Connect a LAN cable from the Linksys to the LAN port on your computer.
Open a browser and enter the Linksys configuration URL
http://192.168.1.1
The default login = admin
The default PW = admin
You can protect your router by changing the default PW (write it down and putit in a safe place)
Go to the wireless configuration and set up the SSID and WPA or WPA2encryption.
Apply these settings to the wireless card in your laptop/computer.

To secure your wireless network from unauthorized access,please click on this link and follow my instructions :- http://www.fixya.com/support/r3559128-wireless_router_security

Need additional information to be sure I'm answering your question, but ... The simplest way to remove a MAC address from a Cisco router: 1) Display the MAC addresses that the router has cached

• show arp

2) Identify the MAC address and associated IP address that needs to be removed For example, let's say the MAC address is 0003.6d1b.4c41 and the IP address is 10.10.10.26: 3) Tell the router to remove the MAC address by calling out the IP address

• clear arp 10.10.10.26

You can verify that the MAC address has been cleared by repeating the 'show arp' command

Note:The Cisco devices here include all Cisco products, like Cisco routers, Cisco catalyst switches, etc. Also apply to the new 2960XR switch, we configured AAA for the WS-C2960XR-48TS-I and WS-C2960XR-24TS-I. here is the procedure: http://www.discountroutercenter.com/how-to-configure-aaa-for-cisco-devices/