Integra Dtr-20.3 THX Select2 Plus AV Receiver - Answered Questions & Fixed issues

Usually the headphone jack has a contact that's "made" by the 'ring' section of the jack when you push in the plug, which bypasses the speaker circuit (that's what automatically silences the speakers when you plug in the headphones when there are no switches to turn the speakers on/off manually)... if the 'ring' strip got bent somehow so it's pressing against that contact all the time, it won't let the speakers' circuit come out of bypass. Look inside the jack with a flashlight... the sideways Vs that touch the 'ring' sections of the stereo headphone plug should be about in the middle of the opening... if they're pushed over too far it may require disassembly to bend them back to the proper position.

You have a defective processor pcb. repair shop must change bd.

The processor pcb board will need to be changed

You will have a defective processor pcb.

:-(

Help here https://www.google.com/search?q=integra+dtr+5.3+goes+into+protect+mode ..

Hi, Please confirm that the remote has power and move closer to the receiver and attempt to use the remote again. If the remote works when you're closer, then this means that your batteries needed to be updated. If the remote does not work even within 1 foot of the receiver, please clean the section of the receiver that receives the remote signal. You can then restart your receiver and attempt to use the remote again. If this fails, then you can attempt to re-program your remote to the receiver once more. Otherwise, you might need to work with Integra to further troubleshoot the possible source of the issue. Thank you.

http://www.integrahometheater.com/faqs.php Check the connections and try a master reset? Perform a master reset. To do the reset you need to turn the receiver on, then on the front panel of the receiver press and hold the "VCR/DVR" button while doing that press the "STANDBY/ON" button. You will see the word "Clear" in the display screen and the receiver will go into standby mode.

You have a short somewhere in the speaker wiring.

You have a defective processor pcb assembly and it must be changed.

You will have bad output transistors, a $124 to 150 repair in shop service

Your DTR-7.8 receiver is not 3D compatible. It does not support the new 1.4 HDMI. You have to have 1.4 HDMI and 1.4 cables for the 3D format.You can bypass your receiver for the video though. Simply run your HDMI cord (1.4) from your Blue Ray to your Projector. Your audio can be ran from your Blue ray to your reciever.

Does this normally happen if you press a few buttons or settings faster in succession? If so then maybe the receiver can't keep up with multitasking or what you would call processing power so maybe just try to not select functions as fast and give it a few seconds in between changing settings before switching to another. my cellphone and receiver will also do this because of lower quality components used in manufacturing. A lot of company's now days to compete with price points are cutting corners so certain components are lacking to keep up with demand of other components in the system.

obviously a short somewhere in the system....

you know what i would do?
pray to god you are still under warranty! XD
its a beautiful machine....

Swap your left and right rear speaker over. If you still get no sound from the right speaker connected to the left speaker connection on the receiver, then you have a fault on the receiver output. Check your manual first to see if any setting switch off the rear speaker before taking the unit for repair or replace

If the display is working, you have audio. Check your amplifier. 1300Watt adaptor ... This unit draws a very low power and that is not needed.

1. Power Off: Turn off the device.
2. Jumper Configuration: Locate the jumper labeled "S16" on the device. Initially, it should be connected to pins 2 and 3.
3. Power On (Alarm+All LEDs Flashing): Turn the device back on. You'll see the alarm LED and all other LEDs flashing.
4. Power Off Again: Turn off the device once more.
5. Jumper Adjustment: Change the jumper configuration from pins 2 and 3 to pins 1 and 2.
6. Finished: Your Porpo YH-2000 is now set to the desired angular unit mode.

If you encounter any issues, you can press the reset switch on the back of the device to reinitialize it.

this model SA rather than SC seems to be a Middle East model. The SC version doesn't have DAB. https://www.google.com/search?q=panasonic+sa-pm250+instruction+manual ..

All questions need clear 'make model (what it is)' first 3 words. https://www.google.com/search?q=fmdott085+V398 ..

Question edited for clarity, typo and CAPS. Question moved from Cars and Trucks category. Claim on the warranty irrespective of how long you have had them. They charge $180 but they cost them $20 to buy from China. Package them up and send them tracked and ask them to replace the batteries. How long is the warranty on AfterShokz? While we hope you never need it, all new Shokz purchased from authorized retailers come with a two-year warranty that begins on your date of purchase. Jan 11, 2019

How To File A Warranty Claim For Your SHOKZ Headphones

https://www.google.com/search?q=Openfit+Shokz+battery+replacement ..