Top 20 HP Compaq WF1907 Monitor Questions & Answers

Refer its user manual for fitting details. Gopakumar Gopalan Google

If you do not log out of facebook when you leave it, it will not ask you to log on when you go back.

Change your preset mode to factory default/normal (maybe ambient sensor?)

Peel off the Compaq logo on the back of the monitor. The other 2 holes are underneath !

Hello,Computer to monitor audio cables are available here: http://www.ccl-la.com/catalog/product_info.php?products_id=176

DVI is a Digital Video Input/Interface. I think what happened is you have changed your inputs on your monitor but that is only if your monitor has several different types of inputs. Check for that and if so then switch your input on your monitor.

Hello, go to www.amazon.com

Enter the model model number and product name.

There you will find out the exact price in dollars.

I hope this helps.

The pen input is not available on the HP W1907 monitor. I have three of them and Win 7 tells me the same thing but there is no firmware in this monitor that supports pen input. There are other models that HP puts out that do and the driver is the same so the option appears in Win 7 by default. Sorry to give bad news. (trust me, I was excited at first followed by the Aw ****!)

This is a well known issue and I have posted a resolution in another area on this site if you try a related search. It involves some thermal paste replacement. However, soon after the post it bit me in the behind and I had a failure. The actual issue is the "trigger" that powers the inverters for the CCFL bulbs gets lost and the circuit turns the bulbs off. If you look close you will see the image is still there but there is no backlight to allow you to see it. There are some Chinese sources that sell the power / inverter board for about $40.00 USD shipping included. I found them via this seller: [email protected] part number: 715G2888-1 Good luck.

• Turn on CPU.
• CPU will be start booting. Red/yellow light will be blinking. If yes then check your monitor light will be fixing and Show *********** Board.
• If shows and your OS will be Booting and fail to start.
• If yes you can repair it.
• Insert OS disk into the DVD driver.
• Turn off PC.
• Turn on
• "Press any key........" when comes this message you press any key.
• After that you can see two option

?? Fresh copy Installation OR

?? Repair Option

• For Repair Press "R"
• It will be start repairing

Thanks.

Hello
Sounds as your video device may be bad,either a onboard chip or a video card.Try using another monitor if you have one or if you can borrow one,if another works then its your monitor.If not then its your video device.

Check your monitor cable first with a used or new one.

Hi Donna,
Please try this,
I am assuming you have Windows XP

Click on "Start" at the bottom left of the screen.
2. Choose "Settings"'
3. Choose "Control Panel"
4. Double click on the "Display" menu option.
5. Click on the "Settings" tab on the display dialog box.
6. Move the resolution slider to a different screen size (e.g. 800x600, 1024x768).
7. Hit the "Apply" button and select "Yes" that you want to use these new settings.
8. Change the resolution back to your preferred setting. Hit "Apply" and "Yes" again.
9. The icon should now be gone for good!

Let me know how it goes.
Thanks

Looks like you may have a hard drive problem or you may have to setup your BIOS due to some kind of BIOS battery or power failer.

You may have power supply or backlights inverter problem, or worst case will be the lamps.
If you are going to DIY and already try the monitor with another PC, and have proper tools and know safety precaution then please read on: Most common failures in the LCD monitors are bad capacitors (bulging top/seal or leaking) in the power supply (they should be replaced in a set), blown fuses; poor solder joints, failed inverter circuits (blown fuse, shorted transistors, shorted/open transformers), bad lamps (poor solder connections or worn out lamps). You will need to open it up and inspect the inside, see example of failed HP monitors to get some ideas what to look for: http://s807.photobucket.com/albums/yy352/budm/ Post back what you see inside so we can guide you further and it will help out other people in the future also.

Basic LCD monitor and TV troubleshooting guide: http://www.fixya.com/support/r6150077-basic_lcd_monitors_troubleshooting http://www.fixya.com/support/r5093881-lcd_flat_panel_tv_troubleshooting_guide http://www.fixya.com/support/r7406380-tv_training_manuals Failed TV and Monitors pictures: http://s807.photobucket.com/albums/yy352/budm/

Learn about bad caps: http://en.wikipedia.org/wiki/Capacitor_plague

Capacitors kit: http://lcdalternatives.auctivacommerce.com/ he can make you a set of caps for you. Or www.digikey.com just make sure to use caps with low ESR, 105c, high ripple current, long life rating such as PANASONIC FM or FC series.

You should check the video cable and also try it with another PC since it is telling you that it is not sensing the video signals from your PC.

Basic LCD monitor and TV troubleshooting guide: http://www.fixya.com/support/r6150077-basic_lcd_monitors_troubleshooting http://www.fixya.com/support/r5093881-lcd_flat_panel_tv_troubleshooting_guide http://www.fixya.com/support/r7406380-tv_training_manuals Failed TV and Monitors: http://s807.photobucket.com/albums/yy352/budm/

Learn about bad caps: http://en.wikipedia.org/wiki/Capacitor_plague

Capacitors kit: http://lcdalternatives.auctivacommerce.com/ he can make you a set of caps for you.

Or www.digikey.com just make sure to use caps with low ESR, 105c, high ripple current, long life rating such as PANASONIC FM or FC series. Please leave rating if it helps.

dvi(white) or vga(blue)? vga you can get at walmart but dvi is not so widely used. i believe they carry it though.. if not try amazon

On the front or top of the display panel are several buttons. The first is the power button, another will be the audio adjust button, there is also a quick view box button that has an icon tha looks like it little monitor. This opens and closes the quick view window, push this button the close the quick view box. Pushing it again should open the quick view box.

I hope that this information was helpful in answering your question.

Brian

digital god, Go here first: http://www.lesliewong.us/blog/2005/05/02/hp-pavilion-f1703-flat-panel-display-blackout-solution/ May be of some help to you. It's an old blog, but do some reading there and then you might decide to fix (DIY) or just trade in for new monitor. If DIY is what you want to attempt, then you will also need to visit YOUTUBE using "lcd monitor disassembly" and "lcd monitor repair" as search terms. Your +5vdc rail seems to be ok! +12vdc rail which supplies the inverter circuit might be in "shut down mode". Inverter takes 12v and makes 500 to 800v ac to light-up the "cold-cathode-fluorescent-lamps" (CCFL's) on the reverse side of the lcd panel. +5v powers the logic interface board (vga to lcd panel conversion) digital stuff! I hope this helped you some. Problem is not anything new in the world of ccfl back-lit-lcd monitors of ALL brands!!! 12fixlouie

Check the monitor on another computer to verify if using correct setting for this monitor will allow a clear image to be displayed.

In windows 7, the monitor should be detected and installed automatically.

What version of windows are you using?

Try another cable, borrow one, then try monitor in another PC / laptop, if it works then either the software settings for the sleep mode are on or it may be a faulty video card.