Top 20
Maytag MFI2067AES Stainless Steel Bottom Freezer French Door Refrigerator Questions & Answers
Maytag MFI2067AES Icemaker is frozen and cannot be
is the fill tube clog? the ice maker is not going to harvest mode. Take the ice maker cover off and put a jumper on T and H hole the dial will turn and wait until you hear the click remove the jumper. make sure you have gloves on. Do this at your own risk, if you are not sure call a servicer. If the dial won't turn you have a bad ice maker (if you have a 115 volts to the ice maker).
11/22/2017 2:24:03 AM •
Maytag...
•
93 views • 0 helpful votes
Handle on bottom freezer door
Hello,
You need to look at the screw at the bottom of the handle. I know this is difficult to do; however, you have to establish what type of inset screw you have to faster.
Most probably, it is a four or five star screw.
You have to have a certain head screwdriver in order to turn the screw in order to secure the handle.
When you identify the head of the screw -- as in four or five head screw -- place the screw driver into the screw and turn until it is firm.
If this does not work, refer to the manufacturer's manual to find a solution.
Hope this works for you. Dana
12/31/2010 3:32:47 AM •
Maytag...
•
184 views • 0 helpful votes
CALLED A REPAIR MAN OUT. REPAIR MAN SAID THE
Rare but possible. I suggest that you order the part yourself and call a serviceman to install it for you. That may be a way to circumvent paying such an exorbitant price for servicing.
12/22/2010 6:48:39 PM •
Maytag...
•
163 views • 1 helpful votes
The water is coming out very slow in water
HI. Usually this will be the cause of a damaged valve or a mineral build up inside the valve that will not allow the valve to open fully. This type of mechanical failure can not be repair, due to the sealed state of the assembly. With that said; Use my procedure to inspect and confirm the damage at hand.
Inlet inspection procedure:
The water inlet valve is located behind your refrigerator. Find the water supply line coming into the valve and turn it off at the source (typically under the sink or in the wall behind the unit). Next; Disconnect the supply line and remove the screws that secure the inlet valve in place.
The water inlet valve is connected by two wires. Label the wire placement on the water inlet valve before disconnecting the wires. The wires are connected to the terminals with slip on connectors
Firmly pull the connectors off of the terminals (do not pull on the wire). You may need to use a pair of needle-nose pliers to remove the connectors. Inspect the connectors and the terminals for corrosion. If the connectors are corroded they should be replaced.
Inspect the filter screen where the supply line connects. Remove any debris or deposits that may have built up using a toothbrush, or warm running water. If you cannot clear the clog, it will be necessary to replace the valve (the filter is not removable on most inlet valves).
Test the water inlet valve for continuity using a multimeter. Set the multimeter to the ohms setting X100 (if available, otherwise use the nearest ohm setting). Place a probe on each terminal. The multimeter should display a reading of 200 to 500 ohms. Close inspection of the inlet valve and especially the coil may reveal the exact ohm resistance rating to test for. If the water inlet valve does not pass this test, it should be replaced.
7/21/2010 9:08:21 PM •
Maytag...
•
292 views • 3 helpful votes
Does the Maytag Model: MSD2651KES have a drip pan underneath?
The Maytag Model MSD2651KES is a side-by-side refrigerator. It does not have a traditional drip pan underneath like some other refrigerator models. Instead, it uses a drain system to collect and channel condensation and defrost water.
The condensation and defrost water from the freezer section of the refrigerator typically flow down through a drain hole and into a drain pan or trough located at the bottom of the refrigerator. This drain pan is usually not accessible from the outside and does not require regular maintenance or emptying.
If you are experiencing any issues with water leakage or pooling around your Maytag refrigerator, it is recommended to check the drain system for any blockages or clogs. Ensure that the drain hole is clear and that the water can flow freely through the system. If you suspect a problem with the drain system, it is advisable to consult the refrigerator's user manual or contact Maytag customer support for specific guidance on troubleshooting and resolving the issue.
6/28/2023 12:36:52 AM •
Maytag...
•
425 views • 1 helpful votes
Not finding what you are looking for?