Pyramid (PS36KX) 600-Watt Power Supply - Answered Questions & Fixed issues

Will the unit power up without the cb radio? I would suggest a short somewhere in the system if the protection light continues to shine bright.

Hi! I saw your question, and maybe this will help. I also have a Texas Star 100w amp, and this same power supply. Even though the nominal draw for your equipment is way below the rated amp flow of the power supply, when you key up, and the output on the amp is at max, you are drawing the limit of your power supply! Try running this setup at a lower linear output. You don't need the full 100 watts to get out! 60-80 watts is aplenty! You should start at a low output, and slowly increase the output(while keyed up), untill the power supply starts to complain.(buzzer/light). This is what your limit will be. The only other cure, is a MUCH bigger power supply. Unfortunately, I cannot afford a 60-90 amp supply, so this is what I am forced to do to use the one we have. Also,keep your cb's output very low when using the linear amp. These amps are supposed to get a low signal from your radio, or the linear amp is overdriven. (noisy and unstable. Hope this helps you! 73's to you! jimsjinx

Needs to get a Depot service done for the Electronic board. Could be an issue with Capacitor or IC. Good luck.

Check the LM723 Regulator IC...it's 14 pins and regulates and adjusts the reference to the pass transistors http://www.eserviceinfo.com/downloadsm/21059/Pyramid_PS-36KX.html

This is alink to the p s 3 6 which is very similar to the PS-35

you have specialist equipment, i recommend it is sent to a specials for calibration.
i could be that the warning is somehow connetied and calibration will ensure that what you dial is exactly was is being supplied.

also this model most likely has cooling and that may be getting blocked check that any air intakes and filters are clean and clear to ensure good airflow if the device is getting hot it may cause the warning light to go on.

also ensure the lines are not shorting anywhere.

I hope this was helpful.

26.46 lbs

Sounds like your filter capacitors are bad or weak and some 60hz ripple is getting through. If you have an oscilloscope, check the output to see if there is any ripple voltage.

Might want to read this

http://www.eham.net/reviews/detail/3442

yes right there is a short circuit in power supply if you are non technical then replace the power supply if you are technical then open the power supply and check the 4diodes of bridge if faulty replace it again check transistor attatched to heat sink if faulty repalce it

THE BEEPS INDICATE THAT THE OVERVOLTAGE PROTECTION IS ACTIVATED,DO NOT HOOK UP ANY THING TO THAT POWER SUPPLY!!!OR THE FULL UNREGULATED VOLTAGE (20-30 VOLTS)WILL PASS FROM THE SHORTED REGULATOR TRANSISTORS TRHU YOUR GALAXY AND FRY IT.GET IT TESTED BY A PRO,USUALLY THE REPLACEMENT PARTS FOR POWER SUPPLY ARE DIRT CHEAP.
GOOD LUCK.

Check all transistors that are atached to
heat sinks , For a short between two of the
three legs. It can't be reset becuse you have
a short.

nothing in this rant for fixya site to answer

Well, look at the pyramid. There are more at the bottom... a lot more less powerful that hat to contribute and pay all to the owners of the land and we're allowed only to survive. In some cases, not even survive, slaves would be worked to ***** in many cases, in some civilizations under the farmers and artisans were thousands more slaves making the bottom of that pyramid wider, allowing for even more riches at the top.

The volume is one third the product of the area of the base times the height or (1/3)B*h

Question translated to English Solo hablamos ingl?s en el sitio web norteamericano. Lamentablemente no tenemos idea de qui?n es este conductor de invierno. Por favor danos m?s informaci?n para ayudarte mejor. Es un problema de seguro de autom?vil, debe comunicarse directamente con la compa??a de seguros. ENGLISH@ We only speak English on the North American website. Unfortunately we have no idea who this winter driver is. Please give us some more information to help you better. It is is a car insurance issue, you need to contact the insurance company direct. ..

DICEUS with 13 years experience. SIMFORM for modernizing legacy architecture. ColorWhistle for leads. PixelCrayons for tailoring to your specific needs.

Keep a backup on your hard drive or a backup. The backup system is a free service supplied by your internet provider. If you use it daily or after every update, there will never be an issue.

If you are in the middle of a contract, then cutting your wages is almost certainly a violation of your employment law rights. While I am by no means an expert on this matter, I did have a similar issue years ago - mid-contract wage cuts - and I hired anemployment attorney to fight the case on my behalf. It turned out that my employer was basically looking to scare people into taking the wage cut. They got into some pretty serious legal trouble for their transgression, and nothing happened to me in terms of wage cuts after that. If you are between contracts, your employer can re-negotiate your salary, but as far as I am aware, if you are in an agreed-upon contract, they cannot just decide to reduce your salary. If you want to settle matters, contest this action with support from a legal professional.

YouTube Backlink Generator https://ovdss.com/apps/youtube-backlink-generator

u need tally 4.5 free software (full ) if u need mail me i will give u link k