Amana NAV5800AW Top Load Washer - Answered Questions & Fixed issues

you could have small item stuckin hole of the washer basket so look an see if there anything in small hole ok

Your pump can be clogged as well. Here is a generic video that shows how to unclog a drain pump.

Maybe door switch? Hear any humming? Belt might be broke. Service Manual If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Try checking for the shipping screws, did you remove them? They are there to prevent the drum moving during transport but if left in the whole machine will try to jump about.

The main bearing seal let go and that is the cause for the noise and water on your floor. The repair is costly, around $350 for repair.

Hello,

The noise you are hearing is the main tub bearing. Water has been leaking past the seal and into the bearing causing it to rust.There is no lubrication on the bearing anymore and you are hearing the metal on metal grinding. You are looking at a costly repair of about $350. I hope this helps you out.

sounds like main tub bearings are gone ..turn the drum by hand if it rumbles its bearing dont use it ... this is not a good job to do.

If the machine works up to that point then the timer is at fault.

Might be a locked up pump or maybe a thrust washer gone out? MORE here If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Here is the fix for "soapy" problem. Follow this link to part.

the motor/ trans / pump / belt / ect yes they are all fine the problem is the timer . the timer stopes the motor after the wash and starts it in the other dir to spin and drain . but this is not happing . so the timer is at fault . pt # 27001088 100.99 hope this helped mm feed back pls

Is it spinning while making the noise?<br /> <br /> <a href="mailto:[email protected]">[email protected]</a><br />

when in some of your wash cycles, try wiggling the timer knob back and forth. sometimes if the timer is going bad the motor will come to life for a split second. if this is the case you need a new timer. if it is completely dead no matter what, you most likely have a bad motor but there is still a chance that there is a bad timer. the odds just increase that it is a bad motor.

u can connect one of them on the hot water valve and turn it on with temperature
if it works then u got the right connection if it doesn't then just swich them on
this is not dangerous

If your Amana washing machine lid is locked and it seems like it's not getting power, there are several steps you can take to troubleshoot the issue. Follow these steps to identify and potentially resolve the problem:

Probably but not advised.

They are around $220 each but vary by model https://www.amanaparts.com/Shop-For-Parts/b1i615/Amana-Door-Boot-Seal-Parts But $40 to 70 on Amazon for a Chinese clone. https://www.amazon.com/s?k=amana+washing+machine+door+seal&crid=DUPKRCGY03XO&sprefix=amana+washing+machine+door+seal%2Caps%2C94&ref=nb_sb_noss ..

Question edited for clarity, 'Amanda' to 'Amana'. Question moved to maker category. It is sensing, and that you have something that needs a 'Delicate' setting, or a 'Woollens' setting. It provides water and very little agitation that might damage or stretch the clothes. Read the manual. Google Amana (model) manual ..

Fiona, could it be that your'e using Liquid color-safe bleach as it is thicker than chlorine bleach and will not dispense properly from the chlorine bleach dispenser? And did you Remove the inserts from the drawer. The inserts are the detergent selector and covers of the softener and bleach dispenser.. and clean and replace them? Tis really hard not being there and being able to see the unit. But thought I'd give you these suggestions. Best to you.