Holding the Cycle End Signal button for 3 seconds is the way to turn the control lock off and on with this model. If that is not unlocking the control like it should, the first thing you would want to try is unplugging it for 5 minutes to let the controls reset.
Best to you
It is possible that the power outlet the washer is plugged into has lost power. Check to see if the outlet is working by plugging in another device. If the outlet is working, then it is possible that the power cord has become loose or disconnected. Check the power cord to make sure it is securely plugged into the wall and to the washer. If the power cord is securely connected, then you may need to call a professional to diagnose and repair the issue.
es, in order to remove the top of a Maytag LSE1000 washing machine, you'll need to first disconnect any attached wires. This is because the wires are connecting important components like the control panel and the sensors to the rest of the machine.
Here are the steps you can follow to safely disconnect the wires:
Unplug the washing machine: Before you begin, make sure to unplug the machine from the power source to prevent any electrical shock.
Locate the wires: Look for the wires that are connecting the top of the machine to the rest of the machine. They should be near the back of the machine where the top and bottom halves of the machine meet.
Label the wires: Label the wires so you know which wire goes where when you're ready to put the machine back together. You can use masking tape and a marker to label each wire.
Disconnect the wires: Gently pull the wires from their connectors, making sure to keep them separated so they don't get tangled. Be careful not to pull too hard, as this could damage the wires or the connectors.
Repeat the process for all the wires: Repeat the process for each wire until they're all disconnected.
Once you've disconnected all the wires, you should be able to remove the top of the machine. Make sure to keep the wires organized and in a safe place while you're working on the machine. When you're ready to reassemble the machine, simply reconnect the wires in the reverse order you disconnected them.
Unplug from the mains. Lower the drain hose into a floor drain or a pail. You should be able to open the door. If not, run another quick wash cycle. The level switch should work now.
It sounds like you are having trouble getting the lid on your Maytag Bravo top-load washer to close properly, even after replacing the lid strike and the lid latch. There could be a few reasons for this issue:
The lid strike and latch are not properly aligned: Make sure that the lid strike and latch are properly aligned and that the strike is lined up correctly with the latch.
The lid strike is not adjusted correctly: The lid strike may need to be adjusted in order to properly engage the latch. Check the installation instructions for the strike to see if there are any adjustment instructions.
The lid latch is in lock mode: Some Maytag Bravo top-load washers have a lock mode that prevents the lid from being opened during a wash cycle. Make sure that the latch is not in lock mode by checking the owner's manual for instructions on how to unlock the latch.
The lid strike or latch are defective: If you've tried the above steps and the lid still won't close, the new strike or latch may be defective. It's recommended to contact the manufacturer for further assistance or to contact a professional technician for repair.
It's important to make sure that the lid is closed properly before starting a wash cycle to prevent water from leaking out of the washer.
If your Maytag washing machine is agitating during the spin cycle, it could be due to a few different issues. Here are some possible causes:
Defective Transmission: The transmission in the washing machine is responsible for shifting the agitator and the drum between the spin and agitation cycles. If the transmission is defective, it may not be able to engage or disengage the agitator properly, causing it to spin during the spin cycle.
Worn Drive Belt: The drive belt connects the motor to the transmission and helps to control the speed and direction of the agitator and drum. If the belt is worn or damaged, it may not be able to properly control the agitator, causing it to spin during the spin cycle.
Malfunctioning Clutch: The clutch in the washing machine helps to regulate the spin and agitation cycles. If the clutch is not functioning properly, it may not be able to disengage the agitator during the spin cycle, causing it to spin along with the drum.
Faulty Timer: The timer controls the various cycles and functions of the washing machine, including the spin and agitation cycles. If the timer is faulty, it may not be able to properly sequence the cycles, causing the agitator to spin during the spin cycle.
It's best to have a professional technician inspect and diagnose the issue to determine the exact cause and the necessary repairs.
It sounds like there could be an issue with either the control assembly or the wiring between it and the washer or dryer. I suggest having a qualified technician take a look at your washer and dryer to check the wiring and control assembly for any problems. The technician should also be able to help you determine the cause of the issue and advise you on how to proceed.
Here are some general steps that may help you remove the tub:
Disconnect power: Turn off the power to the washing machine and disconnect the power cord.
Empty the tub: Remove any clothing or items from the tub.
Locate the retaining clips: The retaining clips are typically located around the perimeter of the tub, near the top of the machine.
Release the clips: Use a flat-head screwdriver or pliers to gently release the retaining clips. Be careful not to damage the clips or the tub.
Check for a retaining nut: If you have difficulty releasing the retaining clips, check to see if there is a retaining nut that needs to be removed. This nut is usually located on the back of the machine, near the bottom of the tub.
Remove the tub: Once you have released the clips and removed any retaining nuts, you should be able to carefully lift the tub out of the machine.
The door switch and the lock for your door and the sensor that lets the door to be able to lock and start up is broken and should have to be replaced. for your washing machine
Question edited for clarity and add 'maker model (what it is)'.
Question moved from Speed Queen to Maytag.
In cold weather an old belt become hard and stiff. When it warms up it is fine. You can either change the belt or you can spray it with Belt Conditioner which helps to soften the rubber and also makes it stickier.
https://www.google.com/search?q=la712+adjust+belt+tensioner
Belt conditioner
https://www.google.com/search?q=belt+conditioner
It's possible that the lid switch is malfunctioning which may prevent the machine from starting on a regular cycle. Inspect the switch for any signs of damage and if necessary, replace it. It is also possible that the timer knob is not properly set or the water level switch is defective. Check these as well to see if they're the culprit.
Power unit down by turning off the circuit breaker or unplugging for one (1) minute. Power unit up by reconnecting power. Restart a new cycle. Monitor the washer for one (1) minute to ensure the error code does not display again.
Best to you
17 The door / cover switch has not been opened since the last two last revolutions. The door did not open after two complete washing cycles. The door switch has not been opened since the last two revolutions. Displays "od". If the door is open, the error disappears. Check the door lock probably bad.
Also you might need to reset it.
...
Press power/cancel then start/pause
Press power/cancel first.
Next, pick a fresh cycle to run.
Press start/pause to reset your Maytag washer.
Run a test load afterward to confirm that the washer has reset.
Hi,
Please power cycle your machine and then rotate the cycle dial by 90 degrees counter clockwise (opposite of usual direction of rotation), then attempt to run a wash cycle again. Otherwise, I would run a rinse cycle and poor some toothpaste in the washer in order to unclog any potential blocks before attempting the wash again.
Thank you.
Hi,
Please try clearing sequences by rotating the cycle dial counter-clockwise a bit before starting a new cycle. The reset should then allow your newly chosen cycle to work.
Thank you.
