20 Most Recent Maytag EPIC MFW9600S - Page 12 Questions & Answers

Normally, switch off for 15 minutes, by flipping the breaker or unplugging, then press and hold the On button for 60 seconds. https://www.google.com/search?safe=off&rlz=1C1QJDB_enCA643CA644&sxsrf=ALeKk01LSRtOYxeOvV1E5FhuoAeNFQj2Eg%3A1603412467138&ei=8yGSX7P4B9KFtQaxjL3IDg&q=maytag+bravos+x+ecoconserve+washer+reset ..

or lid failure possible bad lid switch try jumping for test

If there is no water left after spinning them the problem could be the spin speed. Belt slipping

How warm is the motor getting? Does it take time to cool off and become useable? If so the motor may be overheating and need to be cleaned or have the thermal cutoff replaced.

hi, what is the model of your washing machine? maybe this website can help you to solve your problem http://maytag.manymanuals.com/washing-machines

dU flashes if the following conditions occur: ? Excessive force on door lid is preventing lock bolt from retracting. ? Wash media buildup is preventing lock bolt from retracting. ? Machine/motor control cannot determine if door lock is in an unlocked state.

There is usually several versions of each series of machine and if the capacity isn't marked on the front of the machine you will need to look in the owner's manual against the model number or search the same. It is important not to overload a washing machine to ensure a long and reliable life. Common capacities for domestic washers is 8kg or 9kg and greater capacities tend to be rated business or commercial use. Manufacturers these days urge users of modern computerised washers to weigh laundry loads...

Precise Model number from the Model/Serial tag on the machine (not a user manual) ?

i havent worked on washing machines before as people usually dont bother to fix them and rather buy a new one. however how wedged in is it? could you try prying with a screwdriver? (with the power off just to be safe) and as soon as you get it loose and removed try and insert it in a way it doesnt get stuck and goes in and out freely

This error code indicates excessive detergent suds occurred during the cycle. This could be caused by using too much detergent or not using High Efficiency (HE) detergent. The washer will not be able to spin out water with the excess suds.

Could be a leaky hose on the pressure switch or the switch itself.

Dont bypass it, it is there for a reason. https://www.youtube.com/watch?v=_4U97MQ3d1A

Most washers of my experience have at least one programme that stops the wash, leaving water in the tub until the programmer is advanced a notch by hand when it will pump out and enter the rinse/spin cycles. I suggest you reread the instructions just to be clear whether there is a fault.

How do i reset my maytag front loader washer

new washer

https://www.appliancepartspros.com/parts-for-maytag-mav208daww.html?gclid=EAIaIQobChMI1syprt706AIVJAnnCh1EuA4NEAAYAiAAEgLe-_D_BwE Look for the symptoms and see if they have a video

Yes there is a way to hard reset it, unplug the unit for 5 full minutes to hard reset it. https://www.justanswer.com/appliance/9qr0g-hard-reset-maytag-epic-washer.html Full Reset Disconnect the power to the Maytag dryer and wait 30 minutes. After 30 minutes, restore power and make a new selection. If the problem persists or the dryer will not operate, disconnect power once again and call Maytag for service. https://www.hunker.com/13410587/do-maytag-dryers-have-reset-buttons

https://www.thespruce.com/how-to-clean-a-washer-lint-trap-2147322 Washing machines vary by manufacturers and models and some don't have a lint trap. Lint pumps out of the washer with the water, during the drain and spin cycle, and goes down the drain. https://homeguides.sfgate.com/frontload-washers-lint-trap-89363.html

https://producthelp.maytag.com/Laundry/Washers/Product_Info/Washer_Product_Assistance/F8_E1_or_LF_or_LO_FL_Error_Code_in_Display

some places to check