Top 20 Dual XDM6830 CD Player Questions & Answers

Hi Ant81,

You should only have the Blue wire from the Dual connected the REmote terminal on the Jensen Amp. The Audio cables are the only other wires that connect from the Dual to the Jensen Amp.

Hi. SOunds like another case of power problems. Your deck has 2 power wires. One is yellow th eother is red. One is constant 12 volt battery power, the other is a switched 12 volt power, only has power with the ignition key on or on accesory. Get yourself a test light. I almost bet you do not have the constant 12 volt power to the deck, therefore your deck cannot hold its presets...

this sounds like a wire has cum loose or ur cd player sensor has been damaged

No Simon, that won't work. What you are suggesting is wiring the two horns in series, and that halves the voltage so you would have two horns running on 6 volts. They need to be wired in parallel. A lot depends on how good the horn's relay is and if it can handle the load of two horns. My thought is that it probably will as many vehicles already have twin horns. The positive lead from the relay needs to split and go to the positive sides of both horn, and the negative of the horns to grounds. Ideally, two relays, two horns, two grounds. Look at the YouTube video of the guy that added a huge locomotive twin air horn. It is funny as he goes looking for jay walkers! If I remember he had to install a second battery for it as the load for the air compressor, made the engine stall. ..

GX 1200W 1-Channel Monoblock Class D Amplifier - Phoenix Gold click on manual and download it

You will have to take the CD player apart here in order to get the CD Disc that is stuck inside of the CD player.

Yes. But ... have you knowledge on optimal impedances etc. .......

Audio amps are specialized, the frequency is too low to be used for anything but audio.

videos https://www.google.com/search?q=xdmd9obt+radio+out+of+demo+mode ..

You should try on the search engine box on Google car stereo repairs in Arizona then. Jeff's professional Auto repair Arizona and Quality Car stereos Arizona.

Contact Dual directly to request the diagram.

Request the manual directly from Performance Teknique.

xerox 5755 serial No. 623959

Full wattage or RMS, bridgeable or not .

Hi Chris, from what you said, it would seem like a loose antenna connection problem Review and comment Greetings Franco Dosil Hola Chris, por lo que comentas, parecer?a un problema de conexi?n de antena flojo Revisa y comenta Saludos Franco Dosil http://www.ps2netdrivers.net/manual/dual.xdm6820/

I wouldn't, you need an amp that can support a 1.1 ohm load. I don't know of any head unit onboard amp that can!

https://www.google.com/imgres?imgurl=http%3A%2F%2Fhncdesignperu.com%2Fwp-content%2Fuploads%2Fford-expedition-stereo-wiring-diagram-gooddy-orgaurus-ses-radio-2001-with-2002-mustang.jpg&imgrefurl=http%3A%2F%2F11.nmmd.eprom-filtertechnik.de%2Flhi%2Fmach-460-stereo-wiring-diagram.html&docid=Ejh8a-5GshYzAM&tbnid=t334_82ynBsfKM%3A&vet=10ahUKEwjQ-rXuvfniAhXET98KHSSmAkUQMwhPKAAwAA..i&w=818&h=1198&bih=333&biw=683&q=2000%20expedition%20amp%20wiring%20colors&ved=0ahUKEwjQ-rXuvfniAhXET98KHSSmAkUQMwhPKAAwAA&iact=mrc&uact=8 look at this diagram it should help

Rewire the player to a free (unused) power lug in your fuse box and be sure your ground is connected to something metal instead of tapping into a wire loom.

Hi Robert, whenever you put two or more speakers in parallel, the power handling must be equal in each speaker and the sum total of the power of the speakers, must be greater than the power of the amplifier, to avoid breakages due to excesses of power I hope my comment has served you Greetings Franco Dosil Hola Robert, siempre que pongas dos o mas parlantes en paralelo, el manejo de potencia debe ser igual en cada parlante y la suma total de la potencia de los parlante, tiene que ser mayor a la potencia del amplificador, para evitar roturas por excesos de potencia Espero te haya servido mi comentario Saludos Franco Dosil https://www.bossaudio.com/manual/BE4000D_EN_UM.PDF

Hi there, in reality it does not work that way. The proper way is to contact the company that makes it and become a authorized service and repair person with the company which often inn wolves you paying for it, next after approved you need to buy the access to schematics from the company. Alternatively you can ask you question to get a better answer. You should also post pictures and picture of the circuit board where it connect, list you capabilities so I know what instructions to give, be ready to use a multimeter or a volt o meter.good luck https://www.6ya.com/mr.mike