20 Most Recent
Fisher Paykel EcoSmart GWL15 - Page 4 Questions & Answers
What is code 49
49. (00110001) Phase 2 to 6 - Cold Valve Faulty
The Motor Control Module has measured a voltage from the valve
diagnostic circuit that indicates the cold valve is faulty. The most likely
cause is that the valve harness has not been connected correctly or
the valve is open circuit. See fault 48 for service procedure.
48. (00110000) Phase 2 to 6 - Hot and Cold Valve Faulty
The Motor Control Module has measured voltages from the valve
diagnostic circuit that indicate both the hot and cold valves are faulty.
The most likely cause is that the valve harnesses have not been
connected correctly or the valve is open circuit.
Primary Source: Wiring.
Action: Check the valve harnesses are correctly
fastened to the valves or the pins are not bent
backwards.
Secondary Source: Water Valves.
Action: Check the valve coils are not faulty (open
circuit).
Tertiary Source: Motor Control Module.
Action: Replace the Motor Control Module.
Gw712
66. (01000010) Phase 6 - Pressure Transducer (Ptx)
Error - Frequency > 90 kHz
Note: this supersedes Fault code 65 from V41 Motor Control Module
code onwards.
The Motor Control Module has received signals from the water level
sensor (Ptx) above normal frequency values.
Primary Source: Motor Control Module.
Action: Replace Motor Control Module.
My fisher & paykel GWL 15 washer, began to intake water in a few intervals ( one second ) in and out.Then it stop and make a beep every seconds and the first light at left is on( in washer proces
It could be fault code130
130. (10000010) Single Rotor Position Sensor Error
The Motor Control Module has found an error in the pattern received from the Rotor
Position Sensor. Likely causes of this fault are a bad connection on the harness between the Rotor Position Sensor and the Motor Control Module, or a faulty Rotor Position Sensor.
Primary Source: Wiring.
Action: Check for corrosion on the RAST connector of the Rotor Position
Sensor and the Motor Control Module connector.
Secondary Source: Rotor Position Sensor.
Action: Check the Rotor Position Sensor with an R.P.S. tester. Replace if
faulty.
Tertiary Source: Motor Control Module.
Action: Replace Motor Control Module.
Quaternary Source: Rotor
Action: Ensure the correct rotor for this phase of machine has been fitted
Error code 50
50.(00110010) Hot Valve Coil Faulty
The Motor Control Module has measured a voltage from the valve diagnostic circuit that indicates the hot valve is faulty. The most likely cause is that the valve harness has not
been connected correctly or the valve is open circuit. See fault 48 for service procedure
48. (00110000) Hot and Cold Valve Coil Faulty
The Motor Controller module has measured voltages from the valve diagnostic circuit that
indicate both the hot and cold valves are faulty. The most likely cause is that the valve harnesses have not been connected correctly or the valve is open circuit.
Primary Source: Wiring.
Action: Check the valve harnesses are correctly fastened to the valves or the
pins are not bent backwards.
Secondary Source: Water Valves.
Action: Check the valve coils are not faulty (open circuit).
Tertiary Source: Motor Controller module.
Action: Replace the Motor Controller module.
Fisher and paykel gwl15 has a code 234?
Fault code 234
234. (11101010) Lid Lock Open Circuit
Check Harness to Lid Lock and connections at the Motor Control Module and lid lock ends.
Primary Fault: Connector to the harness, either end could be at fault.
Action: Replace Harness.
Secondary Source: Lid Lock has failed to be activated.
Action:
Tertiary Source:
Action:
Replace Lid Lock.
Motor Control Module has not responded to the Lid Lock being activated.
Check the lid has a tang and is fitted correctly to activate the Lid Lock. If this is all in order, the Motor Control Module must be at fault and needs to be replaced.
Our washer stopped in in mid cycle, was beeping every second with the 3,4 and 8 lights flashing. If the machine is on its beeping and will not do anything
That fault code is 49
49.(00110001) Cold Valve Coil Faulty
The Motor Control Module has measured a voltage from the valve diagnostic circuit that indicates the cold valve is faulty. The most likely cause is that the valve harness has not been connected correctly or the valve is open circuit. See fault 48 for service procedure.
48. (00110000) Hot and Cold Valve Coil Faulty
The Motor Controller module has measured voltages from the valve diagnostic circuit that
indicate both the hot and cold valves are faulty. The most likely cause is that the valve harnesses have not been connected correctly or the valve is open circuit.
Primary Source: Wiring.
Action: Check the valve harnesses are correctly fastened to the valves or the
pins are not bent backwards.
Secondary Source: Water Valves.
Action: Check the valve coils are not faulty (open circuit).
Tertiary Source: Motor Controller module.
Action: Replace the Motor Controller module.
Water coming from magnet housing
That is the seal letting waster past to the bearings
It is loud on spin cycle
It needs a seal and bearing kit installed.
Get a price on this first before you give go ahead for repairs.
Rps sensor on my F&p GW712 as the LED 1 & 7 come on and it beeps and I read somewhere that the problem is the RPS Sensor
Fault code 130
yes it is the RPS
Info on fault 130
130. (10000010) Single Rotor Position Sensor Error
The Motor Control Module has found an error in the pattern received from the Rotor
Position Sensor. Likely causes of this fault are a bad connection on the harness between the Rotor Position Sensor and the Motor Control Module, or a faulty Rotor Position Sensor.
Primary Source: Wiring.
Action: Check for corrosion on the RAST connector of the Rotor Position
Sensor and the Motor Control Module connector.
Secondary Source: Rotor Position Sensor.
Action: Check the Rotor Position Sensor with an R.P.S. tester. Replace if
faulty.
Tertiary Source: Motor Control Module.
Action: Replace Motor Control Module.
Quaternary Source: Rotor
Action: Ensure the correct rotor for this phase of machine has been fitted
Aquasmart lid
Is the lid lock tang on lid broken.
2.9 Lid Lock
The Phase 7 Washer uses the same lid lock that is used on
the Phase 6 series 11 & 12 machines. The difference being is that the lid is now locked for the entire cycle. When the lid is locked the Lid Locked LED will illuminate. Once the spin
has completed, the lock will release and the lid can be
opened. To open the lid during the cycle the
START/PAUSE button must be pressed, the machine will
come to a halt, and the lid locked LED will extinguish.
If the lid is left open, the machine will be unable to lock the lid
and the cycle will be halted. The machine will play a tune
and the lid lock will flash until the lid is closed and START/PAUSE is pressed.
• If the lid-lock fails in the closed position, the locked lid can be forced upwards and out of the
lock. Note: This is the only time in which we would recommend doing this.
• If the harness is damaged, the complete lid lock assembly will need to be replaced.
If the power supply is cut during the spin cycle, the machine will keep the lid locked until the rotor has ceased to turn (3 to 10 secs). Only then will it release the lock. The motor is acting like a generator and allows the lock to stay energized under the bowls inertia.
GWL15 fisher and paykel stops mid spin
If the only light on was the spin when it was beeping,
That is fault code 1
1. (00000001) Motor Control Module Fault
The Motor Control Module has encountered an error when writing to an EEPROM address.
Primary Source: Motor Control Module.
Action: Replace Motor Control Module.
Water pump can't stop running
The motor controller boards needs repair.
The part that controls the pump is locked on.
You need a technician to replace this part.
Fisher&paykel washer will not turn on at all. Is
Yes it is the board dead.
Some common cause is the pump or water in the wrong place.
It could be the pump that has blown the fuse on the board,
Was the pump making loud noise at the time when it died.
if so replace pump and fuse.
Get a technician to replace these parts.
Fisher paykel GWL15 , i have leaking water
Was the pump easy to turn and lock into place.
If it was easy to turn the seal is not seating tight on the bucket.
You need to tighten the four bolts on the gal plate to make pump seal sit tight against the bucket.
I have a fisher and paykell GW712 washing machine
The second light and the seventh light on and beeping is fault 66.
This is info on fault 66.
66. (01000010) Phase 6 - Pressure Transducer (Ptx)
Error - Frequency > 90 kHz
Note: this supersedes Fault code 65 from V41 Motor Control Module
code onwards.
The Motor Control Module has received signals from the water level
sensor (Ptx) above normal frequency values.
Primary Source: Motor Control Module.
Action: Replace Motor Control Module.
Not finding what you are looking for?