20 Most Recent
EnGenius EOC-3220 (EOC3220) - Page 6 Questions & Answers
Cant change router password
If your on windows from a command line type ipconfig /release and reboot..not sure how to call 225-290-5733
1/29/2015 8:29:07 AM •
EnGenius...
•
Answered
on Jan 29, 2015
How do I reset my password for the EnGenius ESR 900?
To reset the password you can hold the reset button down for 5-10 seconds, problem is now you have to set everything back up unless you saved a config file that has all the settings. Don't forget your password next time. :)
8/8/2014 11:56:51 PM •
EnGenius...
•
Answered
on Aug 08, 2014
Edge-core
http://www.youtube.com/watch?v=J-uwpCxbdF8
5/24/2014 7:37:54 PM •
EnGenius...
•
Answered
on May 24, 2014
Username and password, forgot both
If you have changed user/password from default one to your own - which is good - and you have forgot them then you will have to reset the router and set it up from scratch. If you had make a backup of router configuration then try to restore it and check if it will give you a chance to change a password and not log you out after restore.
3/20/2014 10:41:05 AM •
EnGenius...
•
Answered
on Mar 20, 2014
Can't log in Engenius EAP-3660
You don't seem to understand what an Access Point is.
an AP is used to extend your wireless range and will connect to your
router to provide network and internet access. An AP by itself cannot connect to the ISP since it does not use a WAN port
a router is an AP that will allow you to connect to your ISP for internet connection.
A router can be configured to work as an AP but a AP cannot function as a router.
Read the manual. When you reset the AP the IP of the AP device became 192.168.1.1
That means you need to set the IP address of your computer to 192.168.1.x where x is anything from 253-2 and the subnet mask to 255.255.255.0
3/20/2014 7:00:31 AM •
EnGenius...
•
Answered
on Mar 20, 2014
When I enable the vlan option in an EAP9550 I lose wireless access
Bruce,
Is the goal to use a different VLAN for each access point (AP)? If so then you will need to configure each NetGear port to use the same VLAN as the AP that is connected to it. You will then need either a switched virtual interface (SVI) for each VLAN on the NetGear or a trunk port (802.1q) from the NetGear to the Cisco. I'm not sure the NetGear will support SVIs but it will support trunks. An SVI basically creates a gateway for each VLAN's subnet. For example, let's say AP1 uses VLAN 10 and the subnet is 10.0.10.0/24 while AP2 uses VLAN 20 with a 10.0.20.0/24 subnet. The NetGear will need 2 SVIs, one for each VLAN/subnet. The first SVI for VLAN 10 can be configured with IP address 10.0.10.1/24 while the second SVI can be configured with 10.0.20.1/24 for VLAN 20. These IP addresses will be the gateway for each VLAN. Finally, the NetGear would need to act as a router and route each VLAN's subnet to the Cisco device. Once again I don't believe the FS726TP supports this.
The other solution would be to create a VLAN trunk port between the NetGear and the Cisco device but I believe the Cisco RV042 does not support trunking. If it does the trunk would be configured to carry all of the VLANs to the Cisco device which would then have SVIs created on it.
If neither of the above is possible you would need to use the same VLAN for each AP and each of the interfaces on the NetGear and Cisco devices which negates the need for the VLANs.
I hope this helps.
3/16/2014 5:21:41 AM •
EnGenius...
•
Answered
on Mar 16, 2014
Admin password not working
Do a password reset option. The method is listed in the manual that came with the device and if you cannot follow that procedure, go on line to EnGenius . com and look for the support and/or customer service section.
1/29/2014 8:15:51 PM •
EnGenius...
•
Answered
on Jan 29, 2014
Forgot username and password for acess
Is there a tiny hole in the back of the router? Use a straightened paperclip, or similar,. Press in this hole and hold down for twenty seconds to completely reset your router.
1/19/2014 7:06:16 AM •
EnGenius...
•
Answered
on Jan 19, 2014
Not finding what you are looking for?