20 Most Recent Linksys Wireless-N WRT150N Router - Page 7 Questions & Answers

You can log into your router to obtain the WEP key. Usually if you type 192.168.1.1 into your web browser it will take you to the log in screen for your linksys router. The username will be: admin and the password: admin as long as it was not changed. If that username and password does not work then you will need to reset the router by pressing the reset button on the back of it for 10 seconds and then that username and password should work.

Make sure that your computer is able to go online through the modem.
If your computer is not able to go online through the modem then you will need to call ISP first.
If your computer is able to go online through the modem
then you need to connect the computer to the router and the modem to the router.
open the set up page of the router and change the settings of the router according to the ISP.
Click Here for step by step by instructions

This can be due to various problems. Lets try to figure out what is it exactly. First off all see the signal strength at the time that the laptop can not connect.If the signal is just 0-1 lines you may have disconnections. Another point of view is the number of the wireless networks at the area; if there are plenty there might be an interference between yous and one of the others. Try to locate at the router's settings page / wireless connection / channel & ssid and change the channel from auto to manual and try at any of the 13 available channels. Your laptop will locate the new channel automatically.

In case of a problem or clarification, don't hesitate to post me a reply before rejecting my answer.
If you are satisfied, rate my solution with the "thumbs" or (even better) add a testimonial.

Thanks and regards
Please kindly rate this solution
Stelios
direct FixYa link: http://www.fixya.com/users/technical114

hi
visit to the given link
http://homesupport.cisco.com/en-us/wireless/lbc/WRT150N
Hope this has helped you Thanks

If you reset the router, log in via your browser, go to wireless/security and set your security to WPA2.
If you do not have your manual, google "Linksys wrt150n setup"

Hello raviahuja

Try this link: (this works for all wireless routers)

http://www.youtube.com/watch?v=vSAXMO7aNzg&feature=related

Hope that helps.. and if you dont mind rate it :)

Solution for wireless dropping issue or connectivity issues
*Change channels on the router from1,6,11 or 9(rarely works) *Change Channel width 20 or 20/40 MHz *Keep other radio signal emitting or wireless devices away as possible *Change security types *Change Antennas position *Upgrade the firmware

Reset the router for 30 seconds. Then power cycle the router and modem.
Make sure that your computer is able to go online through the modem.
If your computer is not able to go online through the modem then you will need to call ISP first.
If your computer is able to go online through the modem
then you need to connect the computer to the router and the modem to the router.
open the set up page of the router and change the settings of the router according to the ISP.
Click Here for step by step by instructions

If you unplugged your modem then you will have to set it back up which includes putting in your current IP address. The steps are in your user manual and you will need the following information to set it up. If you know the web address for your router you can get the info from that, if not then you will have to contact RCN again. You will need the IP Address, the Gateway address, both primary and secondary, also the subnet mask. But all of that should be explained in the user manual. I would suggest reading it first, writing down the numbers needed and then set it up.

It Might reset the Wireless settings .. Try to reconfigure or Try with A firmware update

CHEEERS

I Think you can do it here .....


CHEERS

Hi ther I ve attached the Picture Just follow the Instruction
OPEN IE and Enter 192.168.1.254 in address and select the same option which ive added .

CHEERS

you have to allow the device to be added to the router table in the rotuer wireless list for the device to access the inter net wirelessly
here are the steps to accomplish this :
1.Log into router
2. Verify wireless router name( on the computer) >>> ( on/off)
3.Note router name you are connecting to.
4.. Check the laptop do ipconfig /all to see current IP addresses.
5. Set the laptop up in the router by WEP KEY or MAC address. This set up in the "security tab" in the router. using 192.168.0.1 or 192.168.1.1 to access through a browser.
6.Note router name you are connecting to.
7. copy and paste this link into the URL and save to favorites or bookmarks / follow the instruction set.

http://www6.nohold.net/Cisco2/ukp.aspx?pid=80&login=1&app=search&vw=1&articleid=20600&donelr=1
This is for all routers to set up wirelessly.

Take a pen or a paper clip and push the reset button on the rear side of the router. It will be like a pin hole. Hold it for about 30 seconds. The Light will go off and come back on showing it is reset. You will get the factory default IP address back again

Try unplugging power to router for about a minute, basically resetting the router and your IP mac address.

Hope this helps

If the Mac Version is 10.3.X or 10..4.X the type the $ symbol infront of password then type your password
Ex:
Your password is 123456789 then type -->$123456789

follow the installation guide/manual.
Download one if you dont have it, you may even find youtube videos to show you

In your case need to check the interference in your room, please check if there's any mirror or glass window which won't allow to pass signals properly, if no then need to change the channel's in the router if it's on auto changed to 20/40 and change the channel...need to try different channels..try this and let us know

IF you are getting public ip from your isp, please go to administrator tab of the router and first change the router's password which is on the top on same page in black dots,,type your new password by deleting old one and re-confirm it just below and save it..router will prompt for the new password just to let you know settings are saved now enable remote managment option on the same page and port is 8080(default, you can use your own port number) and save setting..now you are ready to access your router remotely for that note down the public ip you are getting on your router's status page and in remote location you need to type something like :- http://x.x.x.x:8080...x.x.x.x is your internet ip (public) and 8080 is port number for remote management.

For host applications need to know which application you are running according to that need to open port in the router using Port Forwarding feature of the router.

First of all are you using verizon fiber connection than you don't need any modem, simply connect cable to router's internet port and configure it as pppoe and for you router page if it's not comming properly check which browser you are using if it's IE 8 there's lot of problem try to use firefox and check if it works but still same problem then need to upgrade the firmware of the router download from http://wwww.linksysbycisco.com/download..once upgrade the firmware of the router reset it and reconfigure it for you internet and wireless settings..check and see if it works or not