20 Most Recent
RCA R52WM24 52" HDTV Projection Television - Page 3 Questions & Answers
Color distoted on tv
That can be caused by either the FL231 fuse or the Convergence power board.
www.tvrepairworld.com will assist you in determining which is the cause of the problem if you leave them a email.
Replaced the fl231 fuse tv
Resolder the flyback pins as thats what causes the FL231 fuse to blow. Soldering the flyback should solve the issue you may need to replace the fl231 again
Rca big screen 5-8 years
If you have the original remote to that tv, click on menu, then select set up from the on screen menu, then select convergence. you might see auto convergence as well as manual for blue and red convergence.
If you see Auto, select it, this will line up your tubes.
If no auto convergence, you will have to select each one, and follow the instructions to aline your tubes.
Picture does not fit into
You have to press the hd zoom# or format or wide (or etc.) button on your cable tv or satellite tv remote. If that isn't doing anything then you might have your cable box or satellite tv receiver set on the wrong resolution for your television. Your television's remote might also have a wide or format button on it that needs to be pressed. Also make sure your television is on the right input.
My rca model#r52wm24 has double image yellow and
por lo general ese modelo es un tv de proyeccion .
y ese problema se debe a que le esta fallando uno de los cañones
ya que son tres cañones de pantallan los que trabajan para dar los colores exactos . asi que al fallar un cañon da este tipo de defectos
atentamente :
[email protected]
I'm wanting to drop my satellite service. Will my
Sorry but I've never heard of a DIGITAL ANTENNA, ALL antennas are ANALOG NOT DIGITAL, and yes you will be able to tune in some TV stations if you live close enough of TV stations that still transmit ANALOG signals, with a GOOD VHF/UHF antenna you can have good reception and viable TV time... (best of all it's FREE)
Good Luck!
My rca r52wm24 Tv turns on but after about 20
Hi mcpheeters16,
First to isolate the loose connection from fault, check the cable connectors from the lamp and the ballast board. Pull-out the cables and then re-insert. Also check the ballast board from bad solder joints (crack/cold/dry joints). This is hard to spot I would advice you to work in the brightest area or use table/portable lamp to locate it. Once found, re-solder it.
You have to check also leaky/dried electrolytic capacitor in the ballast board and its power supply. This will do the same symptom. You must have a capacitor checker because not all of it bulged/dome at the top.
Another parts concerned is the lamp itself. Once near to its peak burning life it will produced an intermittent fault like what you've experienced right now.
If you don't have necessary tools and test instrument and can't do the job yourself, I would advice you to look for a qualified technician to troubleshoot the unit.
Hope I helped you.
Have a nice day!
Thanks for using Fixya.
When the picture is on
Now from the symptoms u describe you are haveing a problem with convergence curcits... with these set the first thing you have to determine is you have the comon fl231 fuse problem. to do this read this
http://www.fixya.com/support/r1062030-fl231_problem_convergence_not_in . if this is not your problem then you will have to determine which part of this cuircit is damaged.... do you have convergence setup options.... and can you manually and auto converge these.
Hi I have a convergence issue. Is there a place in
This DLP model RCA tv have convergence menu disappearing is very easy to fix just replaced the convergence fuse FL 231 near the FBT also must be resoldering FBT too.U can buy this FL231 covergence fuse at Ebay.com.No,but u must have to have a soldering iron,a desoring pump or desoldering braids and know how to basic soldering?To replaced this FL231 convergence fuse near the FBT and also must resodering the FBT too for protecting the new FL231 convergence fuse.
I got the tv to show movies on it from my
While playing your movie in your PC, change the screen resolution to lower, and then check your television. The error is in the playing format which your HDTV cannot play while receiving the video signal, which could be of very high resolution or also can be very lower. Try to adjust it, also check your media player properties, might be its conflicting, or some setting should needed to set-up.Check thoroughly for best results.
Can I use a thermal
I wouldn't. Fuses that expire must be replaced with the same type and rating as the original otherwise your safety may be compromised.
I am seeing doubles of
When you go to Menu then setup Do you see Convergence? I fMenu is listing convergence ,then wihTV off Press and Hold CH- and Vol- at same time hold untill Tv comes on,it will either reset Factory settings or let you in Service Menu.
If you Do Not see convergence the you have a blowed Fuse FL231 on the dflection Board ,it will be the bottom lefthand side Board and on the right side of FBT flyback Transfomer is 3 Fuses they are 3 in a roll,small brown looking caps,but are Fuses it will be the one in the Middle.
A curve of red blue yellow lines at the top of
hello it sound like convergance problem go in to the menu on your tv and try resetting the convergance. if don't reset then the convergance ic need to be replaced hope it helps
regards
shaun
Need tp replace power cord
The RCA R52wm24 most likely has a push in cord that is very similar to a computer monitor cord. Radio shack sell them over the counter. Also most TV shops will have them used and sell for a few dollars. WE do all the time.
Please leave feed back
The tv has double vision and shadows
It is the convergence module that needs change, that is what is causing the red green and blue to be out of alignment. You need to change the module.
Not finding what you are looking for?