Symphonic WF20D4 TV - Answered Questions & Fixed issues

0392 0459 0510. Check these codes. If you wish to get more details; check the sites linked here. It has set-up code list & set-up procedure to many popular brand remote controls. Common set-up codes to check with TVs and other devices are given, in the order of the "device's brand name" in alphabetical order. Pull up older posts. Surf the site with patience. Surf the sites by type in the brand name to your set, in its search box. http://electronicshelponline.blogspot.com/ http://remotesearch.blogspot.com/ http://electro-medical.blogspot.com/ http://electrohelponline.blogspot.com/

You should troubleshoot from its main power regulator section circuit. It will be best to contact any service technician.

There should be around 105VDC at the supply end. For more details, refer the repair manual.

As there is no 'Menu'button on the front panel of this TV, to select other inputs, you must have a remote control.

These are the universal remote control codes for Philips. 0062 0204 0184 0208 0205 0206 0207 0004 0189 0183 0199 0200 0288 0456 0003 0008 0068 0075 0086 0087 0141

Try these codes.0053 0189 0227 0456 0024

Check the remote with new batteries. If it do not work, remote control has the trouble. You can't switch the set ON by its front panel power switch, as it has been shut down by remote command.

Use the remote dishnet to automatically detect your code for the tv. Most of the time the procedure is on the remote.

Hi, my name is Cheri Torres and I work on the DISH Internet Response Team. I came across your post recently and would like to help. We have a few different codes for each of our different models of remotes. I will list here for you the best codes for each of our different models or remotes and, the instructions for addressing your remote to your TV. I hope you find this information useful and if you have any further questions or concerns feel free to ask. Remote models Remote codes3.0, 3.1, 3.2, 3.4 IR remotes - codes 569, 632, 733, 694, 569, 846. 5.0, 5.2, 5.3, 5.4 IR remotes - codes 632, 522, 624, 846.4.0 and 4.4 IR/UHF remotes - codes 632, 569, 733, 694.6.0, 6.2, 6.3, 6.4 IR/UHF remotes - codes 733, 632, 694, 756. 569.20.0, 20.1 IR and 21.0 21.1 IR/UHF remotes - codes 632, 733, 756, 846, 679, 694.Instructions for addressing the remote to the TV1. Press and hold down the TV button until all the lights on the remote are lit. 2. Enter the 3 digit code for your remote. 3. Press the pound(#) button once. 4. Test the functionality of your TV. Cheri Torres Internet Response TeamDISH [email protected]

Hello
Just buy one "ATLAS METROCAST -OCAP 5 DEVICE" universal remote control. Symphonic TV is listed with its codes. Codes are:
0180, 0171, 1944
Setup proceedings can be had with its catelogue. OK

This set doesn't have a headphone jack, nor does it have RCA audio output jacks. Without one or the other, you're out of luck connecting headphones to this TV.

I remember a product some years ago that allowed adding headphones using a small microphone placed in front of the speaker. This was hooked to a little amplifier that ran the headphones so the volume could be independently controlled. It was marketed as a way to let "hearing-impaired" family members listen to TV shows without needing to make it uncomfortably loud for others. I haven't looked, but something similar might still be available. It's cumbersome, though, and needs power, plus maybe being costly if you find one.

It's possible to add a headphone jack, but you need to know how to do electronic soldering. Find a spot on the case where you can make a hole and mount a headphone jack, then wire it to the speakers. If you want the headphones to cut off the speakers when plugged in, you need a switching jack, and the speaker wires need to be cut and connected to the correct terminals. The switch built into the jack then disconnects the speakers when the headphone plug is in. If you don't need to turn off the speakers it's a little easier. You just need to wire from the jack to the speaker terminals. I've added jacks on quite a few sets. If you don't feel up to it and don't know anyone who is, you can see if a TV shop (if there are any left in your area!) would do it. (The shop I used to work for charged about $20, including the jack, but that was over 10 years ago now.)

Good luck, and thanks for using Fixya!

Hope one of these works for you.

http://kbase.x10.com/wiki/Universal_Remote_Code_List#X10_Universal_Remote_Code_list

Hello, you may have already gotten this information, but here are some simple steps to get that remote working for your tv. The link below will walk you through a power scan, where you can scan the tv to get the correct code for the DISH remote to your tv.

http://www.dishnetwork.com/SupportSection/power-scan-instructions

and also, here is a link to the codes for the tvs. I hope this helps!!

http://tech.dishnetwork.com/departmental_content/techportal/content/tech/remotes/TechRemo5.3Code.shtml


Becki Barned
DISH Network Customer Service

call 1-800-242-7158 and order another remote. Remote number is Item #NE228UD

Instrucdiones En Espanol

Or, go to your local Superstore (walmart) and purchase a universal remote.

i have a small universal remote and need the codes fir the tv

try this,press manual buttons on tele as if you are changing tv chans ,if you do this thru all mem chans on tele you should come to one that changes to video input this has worked for me on other televisions.

the instructions are on the back of the remote. if lost. you have to:
1) Turn tv on ( i would suggest turning it off then on)
2) Press the Device you want to sync (tv)
3) Press and hold the setup button it will blink once...let it blink twice before you go to the next step.
4) press 9-9-1
5) press the power key on the remote
6) press the channel up (CH +) button repeatedly until the device (tv) turns off.
7) when it cuts off immedieately press the setup button.

According to this spec sheet - No.
http://www.symphonic.us/pdf/spec/2004/wf20d4.pdf

You are correct if your TV doesn't have audio output you can buy an adapter at radioshack or online probably 1/8 to RCA like this one here I’m happy to help further over the phone at https://www.6ya.com/expert/eric_ab7c09ec01841771

Yes you may hook that up to the coaxle end of this unit or the RCA scart connection on the back.

The coaxle end you would need to be on channel 3 or 4 make sure you verify witch channel you vcr is under. Thanks Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/edwy_1a56970cf1ea4620