Unplug or disconnect power to the machine and access the electronic control board. Remove the screws in the back of the top panel, then lift the back of the top panel and slide back to remove.
The electronic control board is located on the left side near the top. It's very common for that part to fail. Look on the back side for a burned or scorched mark near the relays.
Measure the resistance between P1-3 and P1-4. If the resistance is between 1-6 ohms, replace the control board. If not check the belt switch for continuity.
Check the motor windings at the motor switch. Disconnect the motor connector. Measure the run/main windings between the blue wire in back and the white/orange wire (2.4-3.6 Ohms). Measure the start windings between the blue wire in back and the Violette wire (2.4-3.8 Ohms).
Lift the idler pulley up and measure between the two blue wires to check the belt switch.
Ref. link: https://www.applianceblog.com/mainforums/threads/44767-Maytag-Epic-won-t-start
check that there is a small tube in the area as it is around that spot that the pressure hose goes up to the water level selector switch
otherwise use a short metal thread screw with a fibre washer under the head to plug the hole
you can get screws as short is 3/8 to 1/2 " and thick in diameter to fit into the hole
too long and it will bind up on the wash tub
the main board might be damaged due to the damp and cold. the boards don't like wet and damp places as it can damage the copper on the boards causing them to go green and be eaten away, you may be able to repair the board using bridges and repairing the damage.
what you are describing is not due to the leak. There are no fuses in the unit to protect the valves. The fuses protect the whole machine and if they failed, the unit wont power on at all. There is a control panel board on the front and a control board inside the unit near the back top. Check the connections sounds like when the tech cleans the valves that he is wiggling connections that fail later again.
issue him with a written notice of the tear ( also take a photo) so that he cannot blame you for the problem
It is not your fault but normal wear and tear for a machine that old
It sounds like he is trying it on so that you have to fix it
unfortunately it is his machine and repairs are his responsibility regardless of how rough or careful you are
if push comes to shove talk with a lawyer
Sounds like someone may have "hung" on the door whilst it was open, which bent the door or the hinge.
Some hardware stores or appliance stores sell a foam rubber strip with an adhesive backing, wherein you peel off the adhesive cover and stick it on the whatever you want.
Perhaps you could try a piece of sticky-backed foam stuck to the front of the machine or to the door to see if the water will slow down.
God bless your efforts.
The dispenser has three hoses that lead to it. They flush the detergent and softener out when it fills. The hoses to the dispenser can break or come loose and then water runs out of the machine. If the dispenser drawer pulls all the way out, remove it and look in the slot to see if any hoses are loose.
There appears to be variations of this model. Here is a link to one company who may have the parts and assistance you are seeking:
Here are the model number variations:
Error code F 21 means the drain is clogged...follow this advise for the Whirlpool washer as Maytag was bought by themthere is also this site for the washers http://fixedappliance.blogspot.ca/2011/11/whirlpoolkenmoremaytag-more-f02f21-sd.html
Of course. The filter is located in the pump behind 'front' bottom panel. Disconnect power, remove the three screws attaching the lower front access panel to the cabinet then pull the panel down and off the cabinet. You can prop up the bottom front edge of the washer or cushion and lean it against the wall to access and remove the screws more easily. Once the panel is off, remove the filter by turning the knob counterclockwise. Be prepared for a lot of water, catch it in something to prevent more work. Clean the filter from any debris that prevents water from draining out properly. Front loaders hv filters, top loaders don't. Don't forget to click that you are helped!
Sounds like your drain line is clogged. You may also have stuff clogging a water filter just before the pump, or the water outlet coming from the drum.
It could also be a problem with the pump, but until the drain line is opened up, you still won't be able to empty the water from the washer.
Maytag dryer. has no start check door switch. if not door switch then its your relay board that may be bad also check all stats.
there will be 2 at blower cage and 2 on heater assembly
The 2 on blower cage one of these are a resister stat has to be exact resistance or dryer wont start or will start and then shut off dryer b4 it is completed drying hope this helps there should be a cheat sheet paper work that will help you diagnose your problem fallow the steps if not with dryer can be viewed online
